Teledyne Princeton Instruments IsoPlane 81 Manual Download Page 33

Page: 33 / 62

Appendix A:

Technical Specifications

NOTE:

All specifications are subject to change.

This appendix provides technical information and specifications for the IsoPlane 81
system. Additional information may be found on data sheets available on the Teledyne
Princeton Instruments website (

www.princetoninstruments.com

A.1

General System Specifications

Refer to Table A-1 for general system specifications.

Table A-1:

General System Specifications

Parameter

Specification

Minimum

Nominal

Maximum

Read Noise

–

4 e

–

rms @ 200 kHz

7 e

–

rms @ 1 MHz

20 e

–

rms @

4.55 MHz

–

Vertical Shift Rate

a. Software programmable

5.6

sec/row (BRX)

15.2

sec/row (BX)

–

sec/row (BRX)

sec/row (BX)

Nonlinearity

–

<1% @ all ADC rates

Dimensions

Length

–

11 in (26.8 cm)

–

Width

–

7 in (18.0 cm)

–

Height

–

8 in (21.0 cm)

–

Weight

–

19.5 lbs (8.84 kg)

–

Summary of Contents for Princeton Instruments IsoPlane 81































































Search results

Summary of Contents for Princeton Instruments IsoPlane 81

Reviews:

Brands by name

Popular brands

Teledyne Princeton Instruments IsoPlane 81, Manual

Search results

Summary of Contents for Princeton Instruments IsoPlane 81

Reviews:

Brands by name

Popular brands