manualshive.com logo in svg

Teledyne HDO9000, Operator'S Manual

Share
Download
Teledyne HDO9000 Operator'S Manual Download Page 95

Math and Measure

For any parameter that computes on every event, the num statistic represents the number of events

per acquired waveform. If

x

waveforms were acquired, num is

x

times the number of cycles per

waveform.

To reset the statistics counter, touch

Clear Sweeps

on the display or front panel.

Histicons

Histicons are miniature histograms of measurement parameters that appear on the measurement

table. These thumbnail histograms let you see at a glance the statistical distribution of each

parameter. Select the

Histicons

checkbox to turn on histicons.

Tip:

You can quickly display a full histogram by touching the histicon you want to enlarge.

Help Markers

Help Markers clarify measurements by displaying lines, labels and hysteresis bands to mark the

points being measured on the trace. For "@Level" parameters, markers make it easier to see where

your waveform intersects the chosen level.

You can choose to use

Simple

markers, which are only the lines, or

Detailed

markers, which include

the measurement point labels.

You also have the option, by means of the

Always On

checkbox, to leave the markers displayed over

traces after you have closed the Measure dialogs or readout table. If you change the set of

parameters displayed, the markers will change, as well.

Note:

Unlike regular cursors, which are white and can be moved, help markers are blue and

only augment the display; they cannot be moved, and they do not reset the measurement

points. Some optional analysis software packages include markers designed specially for

that domain of reference, which are documented in the option manual.

Detailed Help Markers on standard horizontal parameters.

85

Summary of Contents for HDO9000





























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands