manualshive.com logo in svg

Teledyne HDO9000, Operator'S Manual

Share
Download
Teledyne HDO9000 Operator'S Manual Download Page 40

HDO9000 High Definition Oscilloscopes Operator's Manual

Labeling Traces

The Label function gives you the ability to add custom annotations to the trace display. Once placed,

labels can be moved to new positions or hidden while remaining associated with the trace.

Create Label

1. Select

Label

from the context menu, or touch the

Label

Action toolbar button on the trace setup

dialog.

2. On the Trace Annotation pop-up, touch

Add Label

.

3. Enter the

Label Text

.

4. Optionally, enter the

Horizontal Pos.

and

Vertical Pos.

(in same units as the trace) at which to

place the label. The default position is 0 ns horizontal.

Use Trace Vertical Position

places the

label immediately above the trace.

Reposition Label

Drag-and-drop labels to reposition them, or change the position settings on the Trace Annotation pop-

up.

Edit/Remove Label

On the Trace Annotation pop-up, select the

Label

from the list. Change the settings as desired, or

touch

Remove Label

to delete it.

Clear

View labels

to hide all labels. They will remain in the list.

30

Summary of Contents for HDO9000





























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands