manualshive.com logo in svg

Teledyne HDO9000, Operator'S Manual

Share
Download
Teledyne HDO9000 Operator'S Manual Download Page 39

Using MAUI

To use the virtual keypad, touch the soft keys exactly as you would a calculator. When you touch OK,

the calculated value is entered in the field.

Moving Traces

Use any of these methods to move traces from grid to grid. See

OneTouch Help

for ways to pan

traces within the same grid.

Drag-and-Drop

You can move a trace from one grid to another by dragging its descriptor box to the desired grid. This

is a convenient way to quickly re-arrange traces on the display.

If you are in Q-Scape display mode, you can drag the descriptor box to a grid on another tab, provided

the grid is visible while you are moving the trace. For example, you cannot drag descriptors across

tabs in Q-Scape Single mode, because the target grids aren't visible, but you can in Q-Scape Dual or

Q-Scape Mosaic modes. This is true even in extended display. For more information, see

Display

.

Next Grid Button

Touch twice on the descriptor box of the trace you want moved to open the setup dialog, then touch

the

Next Grid

action toolbar button at the bottom of the dialog. You can also touch and hold (right-

click) the trace descriptor box and choose Next Grid from the context menu.

Note:

If only one grid is open, a second grid opens automatically when you select

Next Grid

.

29

Summary of Contents for HDO9000





























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands