manualshive.com logo in svg

Teledyne HDO9000, Operator'S Manual

Share
Download
Teledyne HDO9000 Operator'S Manual Download Page 174

HDO9000 High Definition Oscilloscopes Operator's Manual

Maintenance

Topics in this section describe procedures for keeping the instrument in optimal working condition.

Touch Screen Calibration

Periodically calibrate the touch screen to maintain its accuracy and responsiveness. We recommend

that you use a stylus rather than your finger for this procedure.

1. From the menu bar, choose

Utilities > Utilities Setup

.

2. On the Utilities main dialog, touch

Touch-Screen Calibration

.

3. Following the prompts, touch as close as possible to the center of each cross that appears on

the screen until the calibration sequence is complete.

Restart/Reboot Instrument

To restart the oscilloscope application, choose

File > Exit

from the menu bar, then touch the

Start

DSO

desktop shortcut.

Note:

You will generally need to exit and restart the application after adding new options keys.

To reboot the instrument, which includes restarting the OS:

1. From within the oscilloscope application, choose

File > Shutdown

from the menu bar. From the

Windows desktop, use the Windows Start Menu Shutdown command.

2. Wait 10 seconds, then press the

Power button

on the front of the instrument.

164

Summary of Contents for HDO9000





























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands