Teledyne HDO9000 Operator'S Manual Download Page 12

Page: 12 / 188

HDO9000 High Definition Oscilloscopes Operator's Manual

Execise care when lifting.

Use the built-in carrying handle.

Do not operate with suspected failures

. Do not use the product if any part is damaged. Obviously

incorrect measurement behaviors (such as failure to calibrate) might indicate impairment due to

hazardous live electrical quantities. Cease operation immediately and sequester the instrument from

inadvertent use.

Operating Environment

Temperature

: 5 to 40° C.

Humidity

: Maximum relative humidity 90 % for temperatures up to 31° C, decreasing linearly to 50%

relative humidity at 40° C.

Altitude

: Up to 3,000 m at or below 30° C.

Cooling

The instrument relies on forced air cooling with internal fans and vents. Take care to avoid restricting

the airflow to any part. In a benchtop configuration, leave a minimum of 15 cm (6 inches) around the

sides between the instrument and the nearest object. The feet provide adequate bottom clearance.

Follow rackmount instructions for proper rack spacing.

Caution:

Do not block the cooling vents.

The instrument also has internal fan control circuitry that regulates the fan speed based on the

ambient temperature. This is performed automatically after start-up.

Calibration

The oscilloscope is calibrated at the factory prior to being shipped. The recommended calibration

interval is one year. Calibration should be performed by qualified personnel only.

Schedule an annual factory calibration as part of your regular maintenance. Extended warranty,

calibration, and upgrade plans are available for purchase. Contact your Teledyne LeCroy sales

representative or

[email protected]

to purchase a service plan.

The oscilloscope software includes both automatic and user-initiated calibration functions. See

Calibration Preferences

Caution:

Remove all inputs prior to performing calibration.

Cleaning

Clean only the exterior of the instrument using a soft cloth moistened with water or an isopropyl

alcohol solution. Do not use harsh chemicals or abrasive elements. Under no circumstances

submerge the instrument or allow moisture to penetrate it. Dry the instrument thoroughly before

connecting a live voltage source.

Summary of Contents for HDO9000





























































































































































































Search results

Summary of Contents for HDO9000

Reviews:

Brands by name

Popular brands

Teledyne HDO9000, Operator'S Manual

Search results

Summary of Contents for HDO9000

Reviews:

Brands by name

Popular brands