Teledyne Everywhereyoulook IsoPlane 320A Manual Download Page 86

Page: 86 / 90

10.

All warranties implied by state law or non-U.S. laws, including the implied warranties of

merchantability and fitness for a particular purpose, are expressly limited to the duration

of the limited warranties set forth above. With the exception of any warranties implied by

state law or non-U.S. laws, as hereby limited, the forgoing warranty is exclusive and in

lieu of all other warranties, guarantees, agreements, and similar obligations of

manufacturer or seller with respect to the repair or replacement of any parts. In no event

shall Princeton Instruments' liability exceed the cost of the repair or replacement of the

defective product or part.

11.

This limited warranty gives you specific legal rights and you may also have other rights

that may vary from state to state and from country to country. Some states and countries

do not allow limitations on how long an implied warranty lasts, when an action may be

brought, or the exclusion or limitation of incidental or consequential damages, so the

above provisions may not apply to you.

12.

When contacting us for technical support or service assistance, please refer to the

Princeton Instruments factory of purchase, contact your authorized Princeton Instruments

representative or reseller, or visit our technical support page at

www.princetoninstruments.com

Contact Information

Roper Scientific's manufacturing facility for this product is located at the following address:

Teledyne

Princeton Instruments

3660 Quakerbridge Road

Trenton, NJ 08619 (USA)

Tel: +1 609.587.9797
[email protected]

Customer Support E-mail:

[email protected]

For immediate support in your area, please call the following locations directly:

France

Germany

Japan

33.1.70.38.19.00

49 (0) 89-660 779 3

81.3.6709.0631

44 (0) 7810 835 719

UK & Ireland

China

86 157 2153 5343

Otherwise, refer to our Support web page at

www.princetoninstruments.com

An up-to-date list of addresses and telephone numbers is posted on the

www.princetoninstruments.com/Support

page. In addition, links on this page to

support topics allow you to send e-mail based requests to the Customer Support group.

Summary of Contents for Everywhereyoulook IsoPlane 320A



























































































Search results

Summary of Contents for Everywhereyoulook IsoPlane 320A

Reviews:

Related manuals for Everywhereyoulook IsoPlane 320A

Brands by name

Popular brands

Teledyne Everywhereyoulook IsoPlane 320A, Manual

Search results

Summary of Contents for Everywhereyoulook IsoPlane 320A

Reviews:

Related manuals for Everywhereyoulook IsoPlane 320A

Brands by name

Popular brands