manualshive.com logo in svg

Teledyne 200A, Instruction Manual, Page: 96 / 220

Share
Download
Teledyne 200A Instruction Manual Download Page 96

Teledyne API Model 200A NO

X

 Analyzer Instruction Manual, 02246, Rev. F1 

 

Table 7-7:  Enabling Dynamic Zero/Span 

StepNumber 

Action 

Comment 

1. Press 

 

SETUP-ACAL 

Causes the M200A go to the AutoCal menu. 

2. Press 

 

PREV-NEXT 

Select the sequence you want for dynamic calibration. 

3. 

Press SET 

Select the SET menu. 

4. Press 

 

PREV-NEXT 

Scroll through the SET menu to the CALIBRATE attribute. 

5. 

Press EDIT 

Set the CALIBRATE attribute value to ON to enable Dynamic 
Span. 

6. 

Press EXIT 

Causes the M200A to return to SAMPLE mode. 

 

NOTE 

If you try a Dynamic span calibration using the NO

2

 permeation tube  

as a calibration gas source, the NO channel concentration will be zero  

due to the lack of NO in the NO

2

 permeation tube. An error message  

will be displayed, CANNOT CALIBRATE. We recommend a calibrated  

NO tank for complete calibration. Also see the CAL-ON-NO2 option. 

 

With dynamic calibration turned on, the instrument will re-set the slope and offset values for the 
NO and NO

x

 channel each day. This continual re-adjustment of calibration parameters can often 

mask subtle fault conditions in the analyzer. It is recommended that if Dynamic Cal is enabled, 
the TEST functions, and SLOPE and OFFSET values in the M200A are checked frequently to 
assure high quality and accurate data from the instrument. 

7-8 

Summary of Contents for 200A





























































































































































































































Reviews:

No comments