manualshive.com logo in svg

Teledyne 200A, Instruction Manual, Page: 81 / 220

Share
Download
Teledyne 200A Instruction Manual Download Page 81

Teledyne API Model 200A NO

X

 Analyzer Instruction Manual, 02246, Rev. F1 

 

6  OPTIONAL HARDWARE AND SOFTWARE 

Optional equipment offered with the M200A includes: 

1.

 

Rack mount with slides (P/N 01469) 

2.

 

Rack mount without slides, ears only (P/N 01470) 

3.

 

Rack mount for external pump w/o tray (P/N 0099701) 

4.

 

Stainless steel zero/span valves (P/N 01468) 

5.

 

Internal zero/span - IZS (P/N 01223) 

6.

 

4-20mA, isolated outputs (P/N 01471) 

7.

 

Internal pump (P/N 01237) 

6.1  Rack Mount Options 

Rack Mount permits the Analyzer to be mounted in a standard 19" wide x 24" deep RETMA 
rack.  

1.

 

Rack mount with slides 

2.

 

Rack mount without slides 

The external pump can be ordered in the following configurations: 

1.

 

External pump pack – standard configuration 

2.

 

Pump pack with rack mount tray to enable slide out servicing 

3.

 

Pump pack with rack mount - fixed tray 

6.2  Zero/Span Valves 

The Zero/Span Valve option consists of two stainless steel solenoid valves. Connections are 
provided on the rear panel for span gas and zero gas inputs to the valves, see Figure 2-2. The 
valves can be actuated by several methods as shown in Table 6-1. 

6-1 

Summary of Contents for 200A





























































































































































































































Reviews:

No comments