Teledyne 200A Instruction Manual Download Page 73

Page: 73 / 220

Teledyne API Model 200A NO

Analyzer Instruction Manual, 02246, Rev. F1

The T

command

lists TEST messages. Examples of the T command are:

T LIST

Lists all active test messages

T LIST ALL

Lists all test messages

T CONVTEMP

Prints the temperature of the moly converter

T LIST NOX

Prints NO

concentration message

T NOX

Prints NO

concentration message

5.5.4 WARNING Commands and Messages

Table 5-16: RS-232 Warning Messages

Name

Message

Description

WSYSRES

SYSTEM RESET

Analyzer was reset/powered on

WRAMINIT

RAM INITIALIZED

RAM was erased

WSAMPFLOW

SAMPLE FLOW WARN

Sample flow out of spec.

WOZONEFLOW

OZONE FLOW WARNING

Ozone flow out of spec.

WRCELLPRESS

RCELL PRESS WARN

Rx cell pressure out of spec

WBOXTEMP

BOX TEMP WARNING

Box temp. out of spec.

WRCELLTEMP

RCELL TEMP WARNING

Reaction cell temp. out of spec.

WIZSTMP

IZS TEMP WARNING

IZS temp. out of spec.

WCONVTEMP

MOLY TEMP WARNING

Molycon temp. out of spec.

WPMTTEMP

PMT TEMP WARNING

Molycon temp. out of spec.

WAUTOZERO

AZERO WRN XXX.X MV

AutoZero filter received a reading out
of limit spec.

WHVPS

HVPS WARNING

High voltage out of spec.

WDCPS

DCPS WARNING

DC Voltage out of spec.

WOZONEGEN

OZONE GEN OFF

Ozone generator is off

WDYNZERO

CANNOT DYN ZERO

Dynamic zero cal. out of spec.

WDYNSPAN

CANNOT DYN SPAN

Dynamic span cal. out of spec.

WVFDET

V/F NOT DETECTED

V/F board not installed or broken

5-33

Summary of Contents for 200A





























































































































































































































Search results

Summary of Contents for 200A

Reviews:

Teledyne 200A, Instruction Manual, Page: 73 / 220

Search results

Summary of Contents for 200A

Reviews: