manualshive.com logo in svg

Teledyne Lecroy PCI Express 3.0 Mid-Bus Probe, Installation And Usage Manual

Share
Download
Teledyne Lecroy PCI Express 3.0 Mid-Bus Probe Installation And Usage Manual Download Page 21

 

PCIe 3.0 Mid‐Bus Probe Installation and Usage Guide

17

Chapter 4

Electrical Design

4.1 

Probe Loading Effect

The logical probing of the PCI Express bus is achieved by tapping a small amount of energy 
from the probed signals and channeling this energy to the analyzer. To avoid excessive 
loading conditions, the Teledyne LeCroy mid‐bus probe employs high impedance tip 
resistors (isolation resistors). The probe isolation resistance is selected to both satisfy the 
probe sensitivity and system parasitic load requirements.

Extensive care has been taken to reduce the parasitic effect of the probed signals during 
each phase of the mid‐bus probe design. The equivalent load model of the Mid‐bus probe 
is available in HSPICE parameters. It is an empirical‐based model that involves complicated 
connectivity. It can be requested from the Teledyne LeCroy Protocol Systems Group 
support team ([email protected]) 

With this unique design, the Teledyne LeCroy mid‐bus probes can capture bus traffic 
signals with amplitudes specified by the PCI Express standard, while introducing only 
slight loss and jitter on the channel under test. To determine the exact numbers, 
customers are encourage to simulate their channel using Teledyne LeCroy’s model.

Summary of Contents for PCI Express 3.0 Mid-Bus Probe































































Reviews:

No comments

Brands by name

Popular brands

Load more brands