CONNECTING THE NUGGET
Included with the Nugget are (one each):
• Base unit
• Coiled handset cord
• User guide
• Handset
• Clear plastic overlay
• Line cord
Contact your supplier or Teledex for information on ordering cus-
tom designed and printed faceplates to enhance the look of your
Teledex Nugget telephone.
1) Located on the left side of the Nugget is a modular jack labeled
TO HANDSET
. Insert one end of the coiled handset cord into this
jack (you should hear the coiled cord click when properly insert-
ed).
2) Insert the other end of the coiled handset cord into the modular
jack on the handset.
3) Turn the telephone so that the back panel is facing you. Insert
one end of the line cord into the jack on the back of the tele-
phone labeled
LINE
.
4) Insert the other end of the line cord into a telephone wall outlet
jack.
5) Once your telephone is connected, place the paper faceplate over
the keys. The plastic overlay slips into place by hooking the tabs
on the overlay into the recessed slots located on both sides. —
The overlay is easiest to insert when; the left or right side tabs
are inserted first, and the middle part of the overlay is slightly
bowed to allow for insertion of the other tabs.
RECEIVING A CALL
1) Lift the handset to connect to the ringing line.
2) To end the call, hang up by replacing the handset.
PLACING A CALL
1) Lift the handset.
2) Listen for dial tone, dial the desired number.
3) To end the call, hang up by replacing the handset.
MESSAGE WAITING LIGHT
The raised red lens is a Message Waiting light. Some telephone systems
permit an operator or message center to turn on the red Message
Waiting light to alert you that you have a message waiting.
Additionally, the Message Waiting light will act as a visual ring indica-
tor, flashing when the telephone is ringing.
USING THE DATA PORT
The DATA PORT is a modular jack, located on the back side of the
telephone, labeled
DATA
. You can connect a facsimile, modem,
answering machine or other device to the telephone line through the
DATA PORT.
To use the DATA PORT:
Insert the modular line cord from your facsimile machine, modem,
etc., into the jack labeled
DATA
.
ADJUSTING THE RING VOLUME
The Nugget has two ring volume settings.
To change the ring volume:
Locate the adjustment control on the back of the telephone labeled
RINGER LOW/HI
. Slide the switch to the desired LOW or HI ring vol-
ume. The ring volume can be changed at any time.
HANDSET VOLUME KEY
The handset has three volume levels. When the handset is first lifted,
the handset volume is normal.
To change the HANDSET VOLUME:
Locate the
HANDSET VOLUME
key to the right of the keypad. Press
the key once and the volume level will increase one level (to medium
volume).
Press the key once more an the volume level will increase an addi-
tional level (to high volume).
To return the handset volume back to normal volume, press the
handset volume key again.
FLASH KEY
Pressing the
FLASH
key initiates a 600ms hookflash. Typical usage is
to access PBX/CO features like call waiting.
RMA PROCEDURES
The following procedure should be followed with all Teledex
telephone products prior to sending the telephone to the factory
for repair.
1) Please perform the tests listed below:
a. Test the telephone on a different telephone jack.
b. Test telephone with a different line cord.
c. Test with a different handset cord (coiled cord).
d. For two line products, please ensure that one of the line
buttons is pressed (if both line buttons are in the UP position,
the telephone will not operate).
2) If the steps listed above do not provide a remedy for the suspect
telephone, please place a tag on the individual telephone
describing the defect. Next, call the Teledex Repair Department
at
1 (800) 875-8539
for an RMA number. You must have an
RMA number to return products to Teledex.
3) Kindly note: An RMA number is unique to each return
shipment. Do not duplicate this number on any future shipments.
SHIPPING INSTRUCTIONS:
Please print the RMA number clearly on the outside of your shipping
carton(s). Please ship to the following address:
Teledex LLC / RMA#___________
6311 San Ignacio Avenue
San Jose, CA 95119
FREIGHT CHARGES:
The Customer is responsible for shipping products for repair to
Teledex. After repair, Teledex will return telephone products to the
Customer freight prepaid in the same manner in which is was sent
(i.e. Freight sent to Teledex UPS Blue, will be returned via 2 day ship-
ping).
**Please note: When telephones are returned for repair due to misuse
(i.e. liquid spills, abuse, or Customer modification - warranty label
broken), the Customer will be charged the standard repair fee, regard-
less of warranty status.
REQUIREMENTS OF PART 68 - FCC RULES
This device has been granted a registration number by the Federal Communications Commission,
under Part 68 rules and regulations for direct connection to the telephone lines. In order to comply
with these FCC rules, the following instructions must be carefully read and applicable portions fol-
lowed completely:
1. Direct connection to the telephone lines may be made only through the standard modular cord fur-
nished, to the utility installed jack. No connection may be made to party or coin phone lines. On
the bottom of the phone is a label that contains among other information, the FCC Registration
Number and the Ringer Equivalence number (REN) for this equipment. If requested this informa-
tion must be provided to the telephone company. The USOC Jack for this equipment is RJ11C.
2. The telephone company, under certain circumstances, may temporarily discontinue and make
changes in facilities and services which may affect the operation of the users' equipment: howev-
er, the user shall be given adequate notice in writing to allow the user to maintain uninterrupted
service.
3. In certain circumstances, it may be necessary for the telephone company to request information
from you concerning the equipment which you have connected to your telephone line. Upon
request of the telephone company, provide the FCC registration number and the ringer equiva-
lence number of the equipment which is connected to your line; this information will be found on
the device.
4. If any of your telephone equipment is not operating properly, you should immediately remove it
from the telephone line. It may cause harm to the telephone network.
5. If the telephone company notes a problem, they may temporarily discontinue service. When prac-
tical, they will notify you in advance of disconnection. If advance notice is not feasible, the tele-
phone company must; promptly notify you of such temporary discontinuance; afford the opportuni-
ty to correct the condition; inform you of your rights to bring a complaint to the FCC under their
rules.
6. Repairs to the device may be made only by the manufacturer or an authorized service agency.
This applies at any time during and after warranty. If unauthorized repair is performed, registration,
connection to the telephone lines and remainder of warranty period all become null and void.
7. This equipment is hearing aid compatible.
REQUIREMENTS OF PART 15 - FCC RULES
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
NUGGET
GUESTROOM TELEPHONE
USERS GUIDE
