manualshive.com logo in svg

Teldat H1 RAIL Series, Installation Manual

Share
Download
Teldat H1 RAIL Series Installation Manual Download Page 21

A.3.5 GPS Connector

The installed GPS connector type is an FME female in those devices equipped with this interface.

PIN

Signal

FME Connector

Internal

RF In

External

Gnd

A.3.6 Configuration Connector

The installed configuration connector is a DB9 female.

PIN

Signal

DB 9 Female

2

RxD (Input)

3

TxD (Output)

5

GND

A.4 Technical Specifications

Hardware Architecture

PROCESSORS

Motorola PowerPC MPC82xx

MEMORY

64 Mbytes in SDRAM

STORAGE UNIT

FLASH Memory (16 Mbytes)

EEPROM 2 Kbytes, NVRAM 128 Kbytes

LAN Interface

PROTOCOLS

Ethernet (802.3)

PORTS

4 port switch managed through MDI/MDX autodetection

SPEED

10/100 Mbps (BaseT)

CONNECTOR

M12 4 Poles Code D

Wireless WAN Interface

STANDARDS

GPRS, UMTS, HSDPA, HSUPA, HSPA+, LTE … Depending on the wireless WAN
version the device has incorporated.

SPEED

Depending on the wireless WAN version the device has incorporated. Please see
the manual on the appropriate module.

CONNECTOR

Up to 4 coaxial connectors, type N

ANTENNA

The antennas are supplied independently to the device

Wireless LAN Interface

Teldat S.A.

Technical Information

Teldat H1 RAIL

17

Summary of Contents for H1 RAIL Series



























Reviews:

No comments

Brands by name

Popular brands

Load more brands