manualshive.com logo in svg

Tektronix TLA7000 Series, Installation Manual

Share
Download
Tektronix TLA7000 Series Installation Manual Download Page 85

Merging Modules

Figure 55: Lining up the two modules

21.

Gently push the two modules together so that the merge connector of the slave
module merges with the connector on the master module.

22.

Slide the modules all the way into the mainframe until they rest against the
rear panel connectors.

23.

Use the injector handles to

fi

rmly seat the modules in place one at a time.

24.

Tighten the four retaining screws on each module to 2.5-in. lbs.

Three-Way Logic Analyzer

Merge Procedure

The following procedure is used for merging three logic analyzer modules
together to form a merged set with a higher logic analyzer channel count.

In a three-way merge (TLA7Nx, TLA7Px, and TLA7Qx logic analyzer modules
only), the master module is in the center. Slave module 1 is to the right of the
master module; slave module 2 is to the left of the master module.

CAUTION.

Static discharge can damage any semiconductor component in the

logic analyzer module.

Discharge the static voltage from your body by wearing a grounded antistatic
wrist strap while performing the merge procedure.

TLA7000 Series Logic Analyzers Installation Manual

67

Summary of Contents for TLA7000 Series


























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands