Tektronix TLA7000 Series Installation Manual Download Page 13

Page: 13 / 121

Service Safety Summary

Service Safety Summary

Only quali

ed personnel should perform service procedures. Read this

Service

Safety Summary

and the

General Safety Summary

before performing any service

procedures.

Do Not Service Alone.

Do not perform internal service or adjustments of this

product unless another person capable of rendering

rst aid and resuscitation is

present.

Disconnect Power.

To avoid electric shock, switch off the instrument power, then

disconnect the power cord from the mains power.

Use Care When Servicing With Power On.

Dangerous voltages or currents may

exist in this product. Disconnect power, remove battery (if applicable), and
disconnect test leads before removing protective panels, soldering, or replacing
components.

To avoid electric shock, do not touch exposed connections.

TLA7000 Series Logic Analyzers Installation Manual

Summary of Contents for TLA7000 Series


























































































































Search results

Summary of Contents for TLA7000 Series

Reviews:

Brands by name

Popular brands

Tektronix TLA7000 Series, Installation Manual

Search results

Summary of Contents for TLA7000 Series

Reviews:

Brands by name

Popular brands