Tektronix TG8000 Technical Reference Download | Manualshive

Page: 13 / 41

background image

Preface

This manual provides information about various PC tools that can be used with
the TG8000 Multiformat Test Signal Generator and related modules.

Products

The information in this manual applies to the following products:

TG8000 Multiformat Test Signal Generator

AG7 Audio Generator Module

AGL7 Analog Genlock Module

ATG7 Analog Test Generator Module

AVG7 Analog Video Generator Module

AWVG7 Analog Wideband Video Generator Module

BG7 Black Generator Module

DVG7 Digital Video Generator Module

GPS7 GPS Synchronization and Timecode Module

HDLG7 HD Dual Link Generator Module

HDVG7 HDTV Digital Video Generator Module

HD3G7 HD 3 Gb/s SDI Video Generator Module

SDI7 Dual Channel SD/HD/3G SDI Video Generator Module

PC Tools

The following utilities and software applications are described in this manual:

TG Setup

Frame Picture Generator

Logo Generator

TG8000 Multiformat Test Signal Generator PC Tools Technical Reference

vii

«
...
11
12
13
14
15
...
»

Summary of Contents for TG8000










































Reviews:

No comments

Related manuals for TG8000

Brand: IDK Pages: 79

Vertex VCE6-HFC-4C

Brand: Spirent Pages: 8

Brand: Karma Pages: 2

Brand: Lindy Pages: 14

samlexsolar SPB-EXPLORE200

Brand: Samlexpower Pages: 2

Brand: NSM Pages: 24

Brand: Goobay Pages: 8

GlobeTrotter Ex GE 0003

Brand: Option Audio Pages: 4

Brand: Black Iris For Telecom & Technology Pages: 14

AZZYRRO 3-6-ZSS-HP

Brand: ZCS Pages: 65

Rack-mountable 8 x 8 USB 2.0 Interface with MX Core DSP Technology 8R

Brand: M-Audio Pages: 25

Brand: CyberPower Pages: 1

Brand: Outback Power Systems Pages: 88

Brand: Centurion Pages: 48

Brand: NAD Pages: 8

Brand: Beghelli Pages: 15

Brand: LG Pages: 23

Brand: Transition Networks Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands