TCA-292MM
Adapter
ZZZ
Instructions
Safety Summary
To avoid potential hazards, use this product only
as speci
fi
ed.
To avoid
fi
re or personal injury
Connect and disconnect properly.
Connect
the adapter to the host instrument before
connecting the 2.92 mm or SMA device to the
device-undertest. Disconnect the device input
and ground from the device-under-test before
disconnecting the 2.92 mm or SMA device from
the adapter and host instrument.
Ground the product.
This product is indirectly
grounded through the grounding conductor
of the host instrument power cord. To avoid
electric shock, the grounding conductor must
be connected to earth ground. Before making
connections to the input or output terminals of
the product, ensure that the product is properly
grounded.
Observe all terminal ratings.
To avoid
fi
re or
shock hazard, observe all ratings and markings
on the host instrument. Consult the host
instrument documentation for further ratings
information before making connections to the
host instrument.
Do not apply a potential to any terminal,
including the common terminal, that exceeds the
maximum rating of that terminal.
Do not operate without covers.
Do not operate
this product with covers or panels removed.
Do not operate with suspected failures.
If you
suspect there is damage to this product, have it
inspected by quali
fi
ed service personnel.
Do not operate in wet/damp conditions.
Do not operate in an explosive atmosphere.
Keep product surfaces clean and dry.
Safety symbols on the product
Product Description
The TekConnect-292MM adapter allows you to
connect 2.92 mm and SMA-terminated devices
to Tektronix instruments with the TekConnect
interface. The adapter preserves maximum signal
integrity and eliminates the need for additional
external adapters, which can degrade voltage
standing wave ratio (VSWR).
Figure 1: TCA-292MM Adapter
Using the Adapter
The adapter connects directly to the TekConnect
interface on the host instrument.
Installing the Adapter
1.
Insert the adapter into the TekConnect
interface on the host instrument until the
adapter locks in place.
2.
Finger-tighten the screw to secure the
adapter to the instrument.
3.
Connect a 2.92 mm or SMA cable to the
adapter.
4.
Connect the other end of the 2.92 mm or
SMA cable to the device under test.
Removing the Adapter
1.
Disconnect the 2.92 mm or SMA cable from
the device under test.
2.
Disconnect the 2.92 mm or SMA cable from
the adapter.
3.
Unscrew the screw that holds the adapter
in place.
4.
Press the button on top of the adapter to
release the lock and remove the adapter
from the host instrument. (See Figure 2.)
NOTE.
It may be necessary to remove the adapter
before installing the host instrument cover.
Figure 2: Removing the adapter from the host
instrument
CAUTION.
Electrostatic discharge (ESD) can
damage the instrument input. Use antistatic
precautions when using this adapter.
Speci
fi
cations
Maximum Input Voltage.
The lesser of 30 V
RMS
or the maximum input voltage rating for the
TekConnect host instrument.
VSWR.
Refer to the TekConnect host instrument
for the overall system VSWR.
Propagation Delay.
142 ps ±4 ps.
Additional Information
For additional information on using the
TekConnect adapters, refer to the documentation
for the host instrument.
Warranty Information
For warranty information, go to
www.tektronix.com, click Support, and
then select Look Up Tektronix Warranty.
Contacting Tektronix
Tektronix, Inc.
14200 SW Karl Braun Drive
PO Box 500 Beaverton, OR 97077 USA
For product information, sales, service, and
technical support:
In North America, call 1–800–833–9200.
Worldwide, visit www.tektronix.com to
fi
nd
contacts in your area.
*P071206401*
071-2064-01
