manualshive.com logo in svg

Tektronix RSA3303B, User Manual

Share
Download
Tektronix RSA3303B User Manual Download Page 34

Functional Overview

1. Display.

Size: 21.3 cm (8.4 inch) Resolution: 800 X 600 dots Color: 256

colors maximum

2. Side Keys.

Select menu items associated with menu keys.

3. Menu keys.

Select menus.

4. Keypad.

Enters alpha and numeric characters.

5. RF input connector

. Connects an input signal. N-type connector, Input

impedance: 50

Ω

. Maximum capacity of non-breakdown input: 30 dBm.

6. Preampli

fi

er power source.

Provides power source for a preampli

fi

er

(optional accessory). (See Table 30 on page 57.)

7. General purpose knob.

Changes a value.

8. Up/Down keys.

Increase or decrease a value.

9. Power switch (ON/STANDBY).

(See page 6,

Turning on the Analyzer

.)

10. LED.

Green on operating, orange on standby.

CAUTION.

Applying a signal of more than +30 dBm may damage the instrument.

Figure 17: Rear panel

22

RSA3303B, RSA3308B, and RSA3408B User Manual

Summary of Contents for RSA3303B
















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands