manualshive.com logo in svg

Tektronix RSA3303B, User Manual

Share
Download
Tektronix RSA3303B User Manual Download Page 30

Calibration

Figure 14: DC offset

To run the DC offset calibration, do the following:

1.

Press the

CAL

key on the front panel.

2.

Press the

Calibrate DC Offset

side key.

The calibration runs. It takes several seconds to complete the process.

Calibrating IF Flatness (RSA3408B Only)

The IF

fl

atness calibration adjusts the IF (intermediate frequency)

fl

atness using

the internal signal generator. It optimizes the

fl

atness of gain and phase within

the IF bandwidth automatically. This calibration is recommended in digital
modulation analysis.

To run the IF

fl

atness calibration, do the following:

1.

Press the

CAL

key on the front panel.

2.

Press the

Calibrate IF Flatness

side key.

The calibration runs. It takes several seconds to complete the process.

Display Brightness Adjustment

Adjust the brightness of the display according to your environment.

18

RSA3303B, RSA3308B, and RSA3408B User Manual

Summary of Contents for RSA3303B
















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands