Tektronix DPO7054 User Manual Download Page 52

Page: 52 / 213

Acquisition

Setting Up Analog Signal Input

Use front-panel buttons to set up your instrument to acquire the signal.

Connect the probe to the input signal source.

CAUTION.

To prevent damage to the instrument, always wear an antistatic wrist strap when making connections to the

instrument and observe the maximum input voltage ratings for input connectors.

MSO70000/C, DSA70000B/C, and DPO70000B/C Series

DPO7000 Series

MSO5000 and DPO5000 Series

Select the input channel by pushing the front-panel buttons to toggle the channels on and off.

MSO5000 and DPO5000 Series

MSO70000/C, DSA70000B/C, DPO70000B/C, and DPO7000
Series

MSO70000/C, DPO/DSA70000B/C, DPO7000, and MSO/DPO5000 Series User Manual

Summary of Contents for DPO7054






















































































































































































































Search results

Summary of Contents for DPO7054

Reviews:

Brands by name

Popular brands

Tektronix DPO7054, User Manual

Search results

Summary of Contents for DPO7054

Reviews:

Brands by name

Popular brands