Tektronix DPO7054 User Manual Download Page 128

Page: 128 / 213

Display a Waveform

Investigate your waveform by moving
from search mark to search mark. Use
the Next (

→

) or Prev (

←

) arrow button

to jump from one marked location to
another, without adjusting any other
controls.

Delete a mark. Push the Next (

→

)

or Prev (

←

) arrow button to jump to

the mark you want to clear. To remove
the center-positioned mark, push the

Set Clr

or the front panel

Set/Clear

button. It works on both manually and
automatically created marks.

To Automatically Set and Clear (delete) Search Marks:

Push

Search

or select

Analyze

Search

Select the desired search type from the
menu.
The search menu is similar to the trigger
menu.
Serial bus searches are optional.

MSO70000/C, DPO/DSA70000B/C, DPO7000, and MSO/DPO5000 Series User Manual

107

Summary of Contents for DPO7054






















































































































































































































Search results

Summary of Contents for DPO7054

Reviews:

Brands by name

Popular brands

Tektronix DPO7054, User Manual

Search results

Summary of Contents for DPO7054

Reviews:

Brands by name

Popular brands