Tektronix DPO3000 Series Service Manual Download | Manualshive

Page: 47 / 79

background image

Maintenance

Power Supply Module

Follow these steps to remove the power supply module. You need to have
previously removed the rear case assembly rear chassis, and I/O board. Use a
TORX T15 screwdriver tip. (See Figure 5-3 on page 5-9.)

1.

Disconnect the power cable from J104 on the I/O board (if still attached)
and from J0403 on the Main board.

2.

Disconnect the cable from the Power Supply module to J0401 on the Main
board.

3.

Disconnect the power connector ground lead from the chassis.

4.

Remove the

fi

ve T15 screws that attach the Power Supply module to the

chassis. When reinstalling torque these screws to 8.0 in/lb.

5.

Lift the Power Supply module, including the power connector, off of the
chassis and place it on a static-free surface.

MSO3000 and DPO3000 Series Digital Phosphor Oscilloscopes Service Manual

4–9

«
...
45
46
47
48
49
...
»

Summary of Contents for DPO3000 Series
















































































Reviews:

No comments

Related manuals for DPO3000 Series

AERAMAX PRO AM3

Brand: Fellowes Pages: 20

Brand: Umount Pages: 2

Brand: La Siesta Pages: 20

Attachment module 180 VIII

Brand: IRUS Pages: 2

LinidoSolutions LI2608.000 Series

Brand: Handicare Pages: 8

Brand: Parkside Pages: 48

Brand: W Box Technologies Pages: 24

Brand: VonHaus Pages: 2

Brand: Rehabmart Pages: 3

Brand: d&b audiotechnik Pages: 11

Brand: hager Pages: 2

Brand: B-Tech Pages: 16

Brand: Songmics Pages: 9

visionary DESIGNS MOD-1298

Brand: Classic Exhibits Pages: 3

Brand: Wali Pages: 5

Brand: Kolpin Outdoors Pages: 7

Brand: Crestron Pages: 12

Brand: NEC Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands