Tektronix DPO2304SX Printable Help Download | Manualshive

Page: 893 / 920

background image

NOTE. These knobs are automatically mapped when certain functions are performed, for example, when the MultiView Zoom
button is pushed.

Bandwidth readout (BW)

Nominal system bandwidth consists of a combination of factors including, but not limited to, probe bandwidth, probe tip
bandwidth, and bandwidth selections made in the Vertical Setup Control Window.

Select the probe controls

From the Vertical menu, select Vertical Setup.

Overview. The Probe controls provide access to the Probe Setup, Compensation, Deskew, and Attenuation control windows.

To use. Click the Probe buttons to display the Probe Setup control windows:

■

to configure the attached probe type. The setup will vary depending on the individual probe you connect.

■

to check the status of the attached probe and to compensate the entire signal path from the probe tip to the

digitized signal.

■

to compensate the vertical channels for propagation delays of different length probes.

■

to change the default attenuation or gain for the selected probe channel.

What do you want to do next?

Learn more about the Attenuation controls.

Learn more about the Deskew controls.

Learn more about the Probe Compensation controls.

Return to the Vertical Setup control window overview.

Oscilloscope reference

DPO70000SX, MSO/DPO70000DX, MSO/DPO70000C, DPO7000C, and MSO/DPO5000B Series

861

«
...
891
892
893
894
895
...
»

Summary of Contents for DPO2304SX

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DPO2304SX

Brand: GE Pages: 14

Brand: GE Pages: 11

Brand: GE Pages: 20

Druck ADTS 2 Series

Brand: GE Pages: 18

Brand: Cadman Pages: 66

Brand: Zetec Pages: 23

Brand: ACDC Pages: 4

Brand: Backyard Discovery Pages: 51

Brand: Nautilus Pages: 12

Brand: CAIRE Pages: 16

Brand: RBC Bioscience Pages: 24

Brand: S&C Pages: 16

Brand: S&C Pages: 23

Brand: UNI-T Pages: 4

UPO3000E Series

Brand: UNI-T Pages: 94

Brand: Underhill Pages: 12

Brand: UMS Pages: 92

i-limb access hand

Brand: Össur Pages: 246

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands