Tektronix DPO2304SX Printable Help Download Page 848

Page: 848 / 920

Probe compensation

Probe compensation adjustment

Probe compensation output

Use the Probe Compensation output to compensate or deskew passive or active voltage probes.

Quality factor

Quality factor is the ratio of eye size to noise.

Quality Factor = (PTopmean – PBasemean)/(PTo PBasesigma)

Recall a template waveform

Use this procedure to recall a template waveform to a reference location.

1. From the File menu click Recall.

2. Under Recall What: click Waveform, and then select the waveform you want to recall.

3. Select Ref <1–4> from the Destination drop-down list.

4. Click Recall.

Oscilloscope reference

816

DPO70000SX, MSO/DPO70000DX, MSO/DPO70000C, DPO7000C, and MSO/DPO5000B Series

Summary of Contents for DPO2304SX

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for DPO2304SX

Reviews:

Related manuals for DPO2304SX

Brands by name

Popular brands

Tektronix DPO2304SX, Printable Help

Search results

Summary of Contents for DPO2304SX

Reviews:

Related manuals for DPO2304SX

Brands by name

Popular brands