Tektronix DPO2304SX Printable Help Download | Manualshive

Page: 611 / 920

background image

4. Adjust the Intensity:

a. Open the Display control window Appearance tab.

b. Rotate the front-panel Intensity knob to adjust the intensity of displayed waveforms, or click in the Intensity FastAcq/

WfmDB entry box and enter the intensity value with the keypad or multipurpose knob.

5. Select the Color Palette:

a. Open the Display control window Colors tab.

b. Click a color palette button in the Fast/Acq WfmDB Palette. In Fast Acquisitions mode, Temp and Spectral show more

detail than the other color palettes.

c. For a definition of each color palette, click

.

Display persistence

From the Display menu, select Display Setup; then open the Appearance tab.
To use

Click one of the buttons to select the display persistence.

■

Click Infinite (persistence) to continuously accumulate record points on the waveform until you change one of the acquisition
display settings.

■

Click Variable; then click in the Time entry box and use the multipurpose knobs to set the persistence time.

■

Click Reset to clear the persistence.

■

Click Controls to activate the Persistence Control window.

Behavior

■

Use infinite persistence for displaying record points that may occur outside the normal acquisition envelope.

■

Use Variable to accumulate record points on the waveform for a specified time interval. Each record point decays
independently according to the time interval.

■

If you click Off, the waveform record points appear for the current acquisition only.

TIP. Use the Display menu Display Persistence submenu or right-click in the graticule and select Display Persistence from
the shortcut menu to directly access the persistence options.

View the analog characteristics of a digital signal

NOTE. iCapture is available only on MSO70000C/DX Series instruments and DPO70000DX Series instruments with option
MSOU installed.

How to ?

DPO70000SX, MSO/DPO70000DX, MSO/DPO70000C, DPO7000C, and MSO/DPO5000B Series

579

«
...
609
610
611
612
613
...
»

Summary of Contents for DPO2304SX

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DPO2304SX

Brand: Calistair Pages: 44

Brand: Landoll Pages: 52

Brand: JBSYSTEMS Light Pages: 14

Brand: YardShape Pages: 50

Brand: Falcon Pages: 52

Brand: Panasonic Pages: 9

WJHD309 - DIGITAL DISK RECORDER

Brand: Panasonic Pages: 7

WJ-ND300 Administrator Console

Brand: Panasonic Pages: 24

Brand: BACtrack Pages: 13

Brand: TA Instruments Pages: 35

Brand: idiag Pages: 12

Brand: ACCU-CHECK Pages: 104

Brand: Pari Pages: 12

Brand: laerdal Pages: 2

Brand: laerdal Pages: 104

Brand: laerdal Pages: 33

Brand: laguna Pages: 16

Brand: Lafayette Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands