Tektronix DPO2304SX Printable Help Download | Manualshive

Page: 243 / 920

background image

LinkTraining

Link training can facilitate debugging the high speed serial link training protocol found in 100G Datacom applications. Standards
include Ethernet and InfinBand using NRZ electrical signaling at 25 Gbps, such as 100GBASE-CR4, CEI LR, 100GBASE-LR4
and CAUI4.

Link Training environment

Oscilloscope channels are used to monitor both directions of a serial lane and present Tx and Link Partner request/response
information for each direction. Analog waveform signaling activity is captured along with Control Channel protocol information to
provide a complete view of the link training process.

Each left/right side of the lane transmits, Coefficient Update Requests for the far transmitter changes, and Status Report
Responses to confirm near transmitter changes.

The oscilloscope eavesdrops on both full-duplex conversations.

Link training activity is passively observed using 20/80 power dividers and differential probing for each lane. The following figure
illustrates typical connection using breakout fixtures, power dividers and P7633 active probes.

DPO70000SX, MSO/DPO70000DX, MSO/DPO70000C, DPO7000C, and MSO/DPO5000B Series

211

«
...
241
242
243
244
245
...
»

Summary of Contents for DPO2304SX

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DPO2304SX

Brand: Ecco Pages: 9

Brand: Talet Equipment Pages: 17

Brand: Bard Pages: 36

Brand: Bard Pages: 2

Brand: Bard Pages: 30

Brand: Bard Peripheral Vascular Pages: 44

Brand: Hammer Pages: 42

Brand: Gebhardt Anlagentechnik Pages: 152

Brand: Hach Pages: 58

Brand: Hach Pages: 52

Brand: iHealth Pages: 8

Brand: Laserworld Pages: 8

Brand: Laserworld Pages: 6

Brand: LaserLiner Pages: 56

Brand: LaserLiner Pages: 54

Brand: Nektar Pages: 12

HQ Power VDL25BM

Brand: Velleman Pages: 3

Brand: iGuzzini Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands