manualshive.com logo in svg

Tektronix AFG31000 Series, Specification And Performance Verification Technical Reference

Share
Download
Tektronix AFG31000 Series Specification And Performance Verification Technical Reference Download Page 27

Specifications 

 

AFG31000 Series Arbitrary Function Generator Specification and Performance Verification Technical Reference 

27 

Characteristic 

Description 

 

   

Resolution 

1 ms or 4 digits 

 

  Total sweep time 

accuracy 

< 0.4% 

 

 

 

 

  Input and output specifications 

The following tables contain input and output specifications for the AFG31000 Series. 

 

  Front panel 

Table 24:  Front-panel input and output specifications 

Characteristic

 

Description

 

Trigger input 

 

  Input level 

TTL compatible 

  Pulse width 

100 ns minimum 

 

  Impedance 

10 kΩ

 

Trigger delay 

 

  Resolution   

(100 ps or 5 digits) 

0.0ns to 85.000s 

Trigger output 

 

  Level 

Positive TTL level pulse into 1 kΩ

 

 

Impedance 

50 Ω, AC 

coupled 

 

  Jitter (RMS), range 

AFG31021, AFG31022, AFG31051, 

AFG31052, AFG31101, AFG31102 

10 ps 

   

AFG31151, AFG31152 

10 ps 

   

AFG31251, AFG31252 

10 ps 

 

 

Summary of Contents for AFG31000 Series



































































Reviews:

No comments

Brands by name

Popular brands

Load more brands