Teknim VAP Series User Manual Download Page 27

Page: 27 / 36

BD-1/07-002

17.2. Setting Date

For VPC016, VPC104, VPC108, VPC116 and VPC132 keypads;

For VPC301 keypad;

18. KEYPAD INNER SETTINGS

These settings can not be done in VPC104 keypad.

Keypad keeps these settings in its memory so configure these settings on which
keypads settings you want to change.

18.1. Chime

Chime is activated when zone is opened or when zone is closed:

Operation

VPC108

VPC016-116

VPC132

VPC301

Open Chime

99 01

(1-8 zone)

99 02

(9-16 zone)

99 01

(1-8 zone)

99 02

(9-16 zone)

99 03

(17-24 zone)

99 04

(25-32 zone)

Keypad setting/Customize/Chime on 1-8

Keypad setting/Customize/Chime on 9-16

Keypad setting/Customize/Chime on 17-24

Keypad setting/Customize/Chime on 25-32

Close Chime

99 02

99 03

(1-8 zone)

99 04

(9-16 zone)

99 05

(1-8 zone)

99 06

(9-16 zone)

99 07

(17-24 zone)

99 08

(25-32 zone)

Keypad Setting/Customize/Chime off 1-8

Keypad Setting/Customize/Chime off 9-16

Keypad Setting/Customize/Chime off 17-24

Keypad Setting/Customize/Chime off 25-32

For VPC016, VPC104, VPC108, VPC116 and VPC132 keypads;



Enter to the master program.

[Enter]

(Program) key long until you hear a long beep.

[Enter] Your 4 digit master code.



[Enter] Address by looking table above.



[Enter] Zone number you want to active chime feature.



[Enter]

(Ok) key.



Enter to the master program.

[Enter] (Program) key long until you hear a long beep.

[Enter] Your 4 digit master code.



[Enter] Address 01 02.



[Enter] Date as shown above table.



[Enter] (Ok) key.



Enter to the master program.

[Enter] (Program) key long until you hear a long beep.

[Enter] Your 4 digit master code.



[Enter] Basic Settings/Clock Setting/Date.



[Enter] Date as shown above table.



[Enter] (Ok) key.

Summary of Contents for VAP Series





































Search results

Summary of Contents for VAP Series

Reviews:

Related manuals for VAP Series

Brands by name

Popular brands

Teknim VAP Series, User Manual

Search results

Summary of Contents for VAP Series

Reviews:

Related manuals for VAP Series

Brands by name

Popular brands