Teknim VAP Series User Manual Download Page 14 | Manualshive

Page: 14 / 36

background image

BD-1/07-002

13

7.1. Enable Bypassing

1

To enter one digit zone number in keypads VPC016, VPC116, VPC132, please enter "0" then

related one digit zone number.

If related zone/zones are bypassed successfully, bypassed zone/zones led and
partition key leds** will be "ON" with bypass led*. The last bypassed zones are saved
in the memory and the old bypassed zones turns back to normal position

Example:

If the 3

rd

zone is currently bypassed, then you bypassed the 2

nd

zone. This

time the 3

rd

zone turns back to normal position. In order to bypass both of them you

have to enter "2", "3" and "bypass" key.

*

There is no bypass led in VPC 301 LCD keypad. Bypass information can be seen in LCD.

**

Partition LEDs are not available on VAP2xx and VAP3xx alarm systems.

7.2. Cancel Bypassing

Please not that armed zones can not be bypassed.

8. ACCESS CODES

According to your system model, there are following codes and authorizations in your
system.

Model

Master

User

Guest

Duress

Engineer

PC Access

VAP204

1

5

1

(no)

1

1

VAP304

1

5

1

1

1

1

VAP308

1

9

1

1

1

1

VAP404

1

5

1

1

1

1

VAP408

1

9

1

1

1

1

VAP416

1

29

1

1

1

1

Default codes are; Master code: 1234*, PC Access code: 7777, User, duress and
guest codes are not entered to the system as default.

*

Please change your master code after installation for your safety.

8.1. Changing Code

Normal users can change their codes as follows;

If the code is changed successfully, you hear a confirmation beep. If not, you hear a
rejection beep and see that trouble light is “ON”. PC Access and Duress code can be
changed only in master program.



[Press] (Bypass) key long.



[Enter] your 4 digit user code.



Select zone/zones that will be bypassed?

1



[Enter] (Ok) key.



[Press] (Bypass) key long



[Enter] your 4 digit user code.



[Enter] (Ok) key.



[Enter] (Program) key long.



[Enter] Your current code.



[Enter] Your new code.



[Enter] Your new code again.



[Enter] (Ok) key.

«
...
12
13
14
15
16
...
»

Summary of Contents for VAP Series





































Reviews:

No comments

Related manuals for VAP Series

Brand: Nacon Pages: 12

Brand: Unipar Pages: 10

Brand: Vacron Pages: 2

Brand: Waters Pages: 116

Brand: i-PRO Pages: 2

Brand: Panasonic Pages: 28

Brand: U-Prox Pages: 3

Brand: AKO Electronica Pages: 50

Brand: Interlogix Pages: 6

Brand: Lorex Pages: 2

Brand: Karaoke USA Pages: 32

Brand: R-Tech Pages: 19

Brand: Pulnix Pages: 44

Brand: TCL Pages: 48

Brand: salmson Pages: 195

Brand: EAW Pages: 2

Brand: TeleCare Pages: 8

Brand: R-Tech Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands