F
R
A
N
Ç
A
I
S
E
S
P
A
Ñ
O
L
®
Teel Submersible Effluent and
Sewage/Solids Handling Pumps
Operating Instructions & Parts Manual
4RK45, 4RK46, 4RK47, 4RK48, 4RK49, 4RK62 and 4RK63
Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.
Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or
property damage! Retain instructions for future reference.
Form 5S4184
®
E
N
G
L
I
S
H
Printed in U.S.A.
09319
0201/020/E3
Unpacking and Inspection
Handle with care. Check items received
against packing list to be sure that all
equipment has been received. Inspect
for shipping damage. If found, file
claim with carrier immediately.
General Safety Information
READ AND FOLLOW
SAFETY INSTRUCTIONS!
This is the safety alert symbol.
When you see this symbol on your
pump or in this manual, look for one of
the following signal words and be alert
to the potential for personal injury.
Warns about
hazards
that will cause serious personal injury,
death, or major property damage if
ignored.
Warns about
hazards that can
cause serious personal injury, death, or
major property damage if ignored.
Warns about
hazards that will or
can cause minor personal injury or
property damage if ignored.
NOTE:
Indicates special instructions
which are important but not related to
hazards.
NOTE:
Pump
must
be installed in a
vertical position
only.
Installing pump
in any other position will void
warranty.
4RK45
Cast iron
Cast iron
Cast iron
Cast iron
20
1
⁄
2
”
16
7
⁄
8
”
20’
117 lbs.
4RK46
Cast iron
Cast iron
Cast iron
Cast iron
20
1
⁄
2
16
7
⁄
8
20
121
4RK47
Cast iron
Cast iron
Cast iron
Cast iron
20
1
⁄
2
16
7
⁄
8
20
122
4RK48
Cast iron
Cast iron
Cast iron
Cast iron
20
1
⁄
2
16
7
⁄
8
20
121
4RK49
Cast iron
Cast iron
Cast iron
Cast iron
20
1
⁄
2
16
7
⁄
8
20
122
4RK62
Cast iron
Cast iron
Cast iron
Cast iron
18
1
⁄
2
16
7
⁄
8
20
120
4RK63
Cast iron
Cast iron
Cast iron
Cast iron
18
1
⁄
2
16
7
⁄
8
20
120
Dimensions
Pump Materials
Dimensions
Cord
Models
Base
Housing
Cover
Impeller
Height
Diameter
Length
Weight
4RK45
1
230
1
8.5
15
130° F
Sewage/solids handling
3”
4RK46
1
230/460*
3
8.5/4.1
15/15
130°
Sewage/solids handling
3
4RK47
1
1
⁄
2
230
1
12.0
15
130°
Sewage/solids handling
3
4RK48
1
1
⁄
2
230/460*
3
9.0/4.7
15/15
130°
Sewage/solids handling
3
4RK49
2
230
1
13.0
20
130°
Sewage/solids handling
3
4RK62
2
230
1
11.0
15
130°
Effluent
2
4RK63
2
230/460*
3
7.5/3.8
15/15
130°
Effluent
2
Specifications
Volts
Motor
Circuit Breaker
Maximum
@
Full Load
Rating
Fluid
Discharge
Models
HP
60 Hz.
Phase
Amps
(Amps)
Temperature
Service
NPT (in.)
Description
Teel submersible effluent pumps, Model Numbers 4RK62 and 4RK63, and
sewage/solids handling pumps, Model Numbers 4RK45, 4RK46, 4RK47, 4RK48 and
4RK49 are used for sewage, effluent and wastewater removal, sump drainage,
liquid transfer systems, circulation, dewatering, and flood control. Pump motors
range from 230V single phase with automatic thermal reset to 230/460V three
phase. 60 hertz, oil filled, 1 HP, 1
1
⁄
2
HP, and 2HP models deliver from 38 to 85 feet
of head with capacities ranging from 20 to 250 GPM.
Volute and semi-open impeller are close grained cast iron. Dual shaft seal,
extended pump out vanes and seal plate barrier provide greater seal protection.
Effluent pumps have 3/4” spherical solids handling capability. Sewage/solids
handling pumps handle 2” spherical solids. Stainless steel hardware for easy
disassembly after extended use. All pumps are manually operated except Model
4RK62, which has an automatic float switch.
* These models are pre-wired at factory for 230V.
