Tecnosystemi Galaxy Proair GAZ100001 Manual Download Page 1

Via dell'Industria 2/4 - z.i. San Giacomo di Veglia

31029 Vittorio Veneto Treviso

Tel. +39 0438 - 500044 / Fax. +39 0438 - 501516

 

- TOLL FREE NUMBER IN ITALY 800 904474

[email protected]

www.tecnosystemi.com

REV. 00 / 09-06-2020

CODE CLI00060

WALL-MOUNTED LEM RF ROOM PROBE WITH BATTERIES 

IN RADIO FREQUENCY

CODE GAZ100001

multi-zone

proAIR

1. TECHNICAL SPECIFICATIONS

3. FASTENING THE LEM PROBE 

4. CONFIGURING THE LEM RF SENSOR IN A PROAIR SYSTEM

TECHNICAL SPECIFICATIONS

•  Power supply: 2 x 1.5 V AAA BATTERIES (LR03) included

•  Battery duration: 18 months

•  Data transmission: in rf radio frequency at 868 Mhz

•  RF signal range 50 metres max in open field between the probe and polaris 2X/3X control 

panel

•  Room temperature sensor

•  Humidity sensor

•  Blue LED indicator which comes on every 60 seconds

•  Fastening: on the wall using template, screws and wall plugs included.

The LEM RFroom  probe  IS a proair system element which, when installed in a room, 

detects the zone temperature and the humidity threshold and sends the values to 

the polaris 2X / 3X CONTROL PANEL.

The  LEM RF  room  probe  replaces  all  the  system  chrono-thermostats, 

except for the 

master chrono-thermostat.

 

The  configurations

  of  the  probe  to  the  system  and  the 

setting are done directly 

from the polaris 2X/3X CONTROL PANEL, the master chrono-

thermostat or from the App

 (if installed).

2. DIMENSIONS AND COMPONENTS

 106 

 65 

 19 

 5 

 17 

65

106

19

5

17

LEM 

WITH INSTALLATION 

TEMPLATE

INSTALLATION 

TEMPLATE

WALL-MOUNTED

LEM

LEM ROOM PROBE

INSTALLATION TEMPLATE

WALL PLUG

SCREWS

SCREWS

WALL PLUG

View from above

IT is important that a Proair system with one or more LEM RF room probes

 includes at least one 

Discovery 2X RF master chrono-thermostat or a STEALTH 2X cabled chrono-thermostat. 

Proair system 

CANNOT work

 with LEM RF room probes only.

Front view

STATUS LED FOR LEM RF SENSOR

CONFIGURATION 

AND RESET BUTTON

BATTERY SLOT

1.5V TYPE AAA

BATTERY SLOT

1.5V TYPE AAA

Rear view

•  Insert the batteries supplied respecting the polarity

CAUTION: Always replace both the old batteries with new ones. The batteries are 

considered to be special waste and must be disposed of accordingly. Observe the 

regulations in force at the collection points in your area.

CAUTION: Do not use rechargeable or lithium batteries because they do not last 

as long. Tecnosystemi recommends using alkaline batteries.

•  When switching on the first time (if it has never been associated with a zone before), 

check that the blue status LED flashes rapidly (the LEM RF room probe searches for 

the control panel ID signal for 2 minutes before switching off).

•  Power on the Polaris 3X control panel or, if it is already powered on, allow visibility of 

the control panel ID from the menu Configuration - Control panel info. This procedure 

must occur within 2 minutes before the status LED stops flashing rapidly. If necessary, 

press the button on the back of the LEM RF room probe to start searching for the ID 

again.

•  When the Polaris 3X starts sending the ID signal, the status LED will stop flashing 

rapidly and flash just once. Now, assign the desired zone based on the info in the table.

CONFIGURING THE LEM RF ROOM PROBE

ZONE No. 

TO ASSIGN

NUMBER OF TIMES 

TO PRESS 

THE BUTTON

CONFIRM 

ZONE

CHECK 

ZONE

2

1 press

Press for 5 sec.

2 LED flashes

3

2 presses

Press for 5 sec.

3 LED flashes

4

3 presses

Press for 5 sec.

4 LED flashes

5

4 presses

Press for 5 sec.

5 LED flashes

6

5 presses

Press for 5 sec.

6 LED flashes

7

6 presses

Press for 5 sec.

7 LED flashes

8

7 presses

Press for 5 sec.

8 LED flashes

9

8 presses

Press for 5 sec.

9 LED flashes

10

9 presses

Press for 5 sec.

10 LED flashes

11

10 presses

Press for 5 sec.

11 LED flashes

12

11 presses

Press for 5 sec.

12 LED flashes

13

12 presses

Press for 5 sec.

13 LED flashes

14

13 presses

Press for 5 sec.

14 LED flashes

15

14 presses

Press for 5 sec.

15 LED flashes

16

15 presses

Press for 5 sec.

16 LED flashes

Reviews: