manualshive.com logo in svg

technoswitch ORYX200 Series, Installation & Operation Manual

Share
Download
technoswitch ORYX200 Series Installation & Operation Manual Download Page 35

ORYX202 ORYX204 ORYX208 Conventional Fire Panels 

– INSTALLATION & OPERATION MANUAL 

 

 
PRMAN-0047 ORYX200 S21 Fire Panel Range Rev 02.00 220224.docx 

E&OE 

- 35 - 

3.1.2 

RELAYS 

The Relays have the following programmable features: 

Programming 
Group 

Programming  
Function 

Comments 

Options 

None 

Not in Use 

The output is not used and will not 
activate. 

None 

General 

Fault 

The output is activated when a general 
fault is activated. 

Output Text: 0

–21 Characters 

Enabled: YES/NO 
Test: YES/NO 

 

External Fault 

The output is activated when an 
external fault is activated. 

Output Text: 0

–21 Characters 

Enabled: YES/NO 
Test: YES/NO 

 

Supply Fault 

The output is activated when a supply 
fault is detected. 

Output Text: 0

–21 Characters 

Enabled: YES/NO 
Test: YES/NO 

 

Sounder Fault 

The output is activated when a 
sounder fault is detected. 

Output Text: 0

–21 Characters 

Enabled: YES/NO 
Test: YES/NO 

 

Sounder Silenced 

The output is activated when a 
sounder is silenced. 

Output Text: 0

–21 Characters 

Enabled: YES/NO 
Test: YES/NO 

 

Sounder Activated 

The output is activated when a specific 
sounder is activated. 

Output Text: 0

–21 Characters 

Enabled: YES/NO 
Test: YES/NO 

 

Sounder Disabled 

The output is activated when a 
sounder is disabled. 

Output Text: 0

–21 Characters 

Enabled: YES/NO 
Test: YES/NO 

 

Disablement 

The output is activated when an FACP 
device is disabled. 

Output Text: 0

–21 Characters 

Enabled: YES/NO 
Test: YES/NO 

 

Test 

The output is activated when an FACP 
device is put into test mode. 

Output Text: 0

–21 Characters 

Enabled: YES/NO 
Test: YES/NO 

 

Fire 

The output is activated when a general 
fire alarm is activated. Repeater relay 1 
default to this setting. 

Output Text: 0

–21 Characters 

Enabled: YES/NO 
Test: YES/NO 

 

Coincidence 

The output is activated when any 
2 zone fire alarms are activated. 

Output Text: 0

–21 Characters 

Enabled: YES/NO 
Test: YES/NO 

 

Reset 

The output is activated for 
approximately 10-15 seconds when the 
panel is reset. 

Output Text: 0

–21 Characters 

Enabled: YES/NO 
Test: YES/NO 

 

Controls Enabled 

The output is activated when the 
controls are enabled.  

Output Text: 0

–21 Characters 

Enabled: YES/NO 
Test: YES/NO 

 

Supervisory 

The output will activate when a 
supervisory signal is detected. 
Repeater relay 2 default to this setting. 

Output Text: 0

–21 Characters 

Enabled: YES/NO 
Test: YES/NO 

 

Fire SND 

The output is activated when any fire 
sounder is activated. 

Output Text: 0

–21 Characters 

Enabled: YES/NO 
Test: YES/NO 

Summary of Contents for ORYX200 Series


















































Reviews:

No comments

Brands by name

Popular brands

Load more brands