manualshive.com logo in svg

technoswitch ORYX200 Series, Installation & Operation Manual

Share
Download
technoswitch ORYX200 Series Installation & Operation Manual Download Page 34

ORYX202 ORYX204 ORYX208 Conventional Fire Panels 

– INSTALLATION & OPERATION MANUAL 

 

 
PRMAN-0047 ORYX200 S21 Fire Panel Range Rev 02.00 220224.docx 

E&OE 

- 34 - 

3 

PROGRAMMABLE FEATURES AND MENU STRUCTURE 

The following programmable features are configured using the SOLAR software. The SOLAR software can be 
downloaded from the Technoswitch website 

www.technoswitch.co.za

. 

SOLAR is a Windows application used to configure the Technoswitch ORYX and RHINO Fire Control and 
Extinguishing panel ranges. The minimum operating system requirement for the SOLAR Software is Windows 7. 
SOLAR uses a USB-B cable to communicate with the panels (refer to 1.9.7 USB Connection for SOLAR on 
page 26). 

3.1 

PROGRAMMABLE FEATURES 

3.1.1 

ZONES 

The Zones have the following programmable features: 

Options 

Function 

Comments 

Default Settings 

Mode 

Immediate 

Zone indication and Sounders are activated 
immediately. Sounder delays are cancelled. 

Normal 

 

Normal 

Zone indications are activated immediately. 
Sounder will only be activated after the set 
sounder delay period has lapsed. 

 

 

Verified  
 

Determines the minimum time that the circuit 
must be in the alarm condition before an alarm 
condition is registered. 

 

 

Confirmed 

1st alarm from a zone is inhibited, zone is reset 
and checked every 30 seconds.  
If the alarm is still present after 30 seconds, the 
panel generates a full fire condition.  
If alarm is not present after the 30 second 
continue check.  
If a new alarm is received from the same zone 
within 30 minutes, a full fire alarm is generated.  
After 30 minutes if no alarm was received, the 
confirmation check cycle will restart 

 

Type 

Normal  

Normal detection only 

Normal 

 

IS (MTL 5561) 

Two Channel MTL Galvanic Isolator  

 

Enabled 

Yes 

Zone is enabled 

Yes 

 

No 

Zone is disabled 

 

Test 

Yes 

Zone is in walk test 

No 

 

No 

Zone is in normal operation 

 

Verification Time 

10 to 60 seconds 

Used in conjunction with verified mode. Set the 
minimum time that the circuit must be alarm 
condition before a fire alarm condition is 
registered. 

0 

 

 

 

Summary of Contents for ORYX200 Series


















































Reviews:

No comments

Brands by name

Popular brands

Load more brands