manualshive.com logo in svg

technoswitch ORYX200 Series, Installation & Operation Manual

Share
Download
technoswitch ORYX200 Series Installation & Operation Manual Download Page 31

ORYX202 ORYX204 ORYX208 Conventional Fire Panels 

– INSTALLATION & OPERATION MANUAL 

 

 
PRMAN-0047 ORYX200 S21 Fire Panel Range Rev 02.00 220224.docx 

E&OE 

- 31 - 

2.1.3 

ENABLE CONTROLS 

To enable controls, turn the Enable Controls key switch clockwise into the position as shown below. The 
Controls Enabled LED will indicate Steady Yellow as confirmation. The key switch cannot be removed in the 
Enabled position.  

Controls Disabled 

Controls Enabled 

 

 

2.1.4 

RE-SOUNDING OF SOUNDERS (EVACUATION) 

▪

 

The following procedure is used to resound the alarm sounders:  

Press and hold  

  for 3 seconds. 

The General Fire LED and both Sounder Circuits will be on. 

2.1.5 

ENABLING/DISABLING OF ZONES 

▪

 

The following procedure is used to disable a zone:  

Press and hold  

 for 3 seconds. 

The General Disable LED and Zone 1 Fault /In Test/Disable LED will both 
flash rapidly Yellow. 

Press   

 (scroll) to move on to the 

zone to be disabled. 

Each press of the scroll button will advance the selection onto the next 
zone (i.e., two presses will select Zone 3) and this will be confirmed by the 
respective Zone Fault/In Test/Disable LED flashing rapidly. 

Confirm your selection by pressing

   

once. 

The General Disable LED and the selected zone

’s Fault/In Test/Disable 

LED will now be on steady Yellow. The rapid flashing LED will 
automatically advance the selection onto the next zone. 

 

To exit the enablement or disablement selection mode wait for 10 seconds 
or press reset. 

▪

 

The same procedure is used to enable a zone. 

2.1.6 

ENABLING/DISABLING OF SOUNDER CIRCUITS 

▪

 

The following procedure is used to disable sounder circuits:  

Press and hold  

 for 3 seconds. 

The General Disable LED and Zone 1 Fault /In Test/Disable LED will both 
flash Yellow. 

Press   

 (scroll) to move on to the 

sounder circuits to be disabled. 

Each press will advance the selection onto the next zone and then after the 
last zone onto the SOUNDER Fault/Disable LED. This will be confirmed by 
the SOUNDER Fault/Disable LED flashing rapidly. Confirming this will 
result in both Sounder Circuits being disabled.   

Confirm your selection by pressing  

 once. 

The General Disable LED, Sounder Fault/Disable LED and both SNDR 
Fault LEDs will now be on steady Yellow. The rapid flashing LED will 
automatically advance the selection back to zone 1. 

 

To exit the enablement or disablement selection mode, wait for 10 seconds 
or press reset. 

▪

 

The same procedure is used to enable a sounder circuit. 

2.1.7 

ENABLING/DISABLING OF PROGRAMMABLE INPUT CIRCUITS 

▪

 

Please refer to the SOLAR Help Guide (PRMAN-0049 SOLAR) to set this feature. 

Summary of Contents for ORYX200 Series


















































Reviews:

No comments

Brands by name

Popular brands

Load more brands