Technosoft iPOS4808MY Technical Reference Download | Manualshive

Page: 7 / 25

background image



Technosoft 2016

7

IO-iPOS4808MY Technical Reference

1.2 Cautions

CAUTION!

THE POWER SUPPLIES CONNECTED TO THE DRIVE MUST COMPLY

WITH THE PARAMETERS SPECIFIED IN THIS DOCUMENT

CAUTION!

TROUBLESHOOTING AND SERVICING ARE PERMITTED ONLY FOR

PERSONNEL AUTHORISED BY TECHNOSOFT

CAUTION!

THE DRIVE CONTAINS ELECTROSTATICALLY SENSITIVE

COMPONENTS WHICH MAY BE DAMAGED BY INCORRECT

HANDLING. THEREFORE THE DRIVE SHALL BE REMOVED FROM ITS

ORIGINAL PACKAGE ONLY IN AN ESD PROTECTED ENVIRONMENT

To prevent electrostatic damage, avoid contact with insulating materials, such as synthetic fabrics or plastic

surfaces. In order to discharge static electricity build-up, place the drive on a grounded conductive surface

and also ground yourself.

«
...
5
6
7
8
9
...
»

Summary of Contents for iPOS4808MY


























Reviews:

No comments

Related manuals for iPOS4808MY

Brand: National Instruments Pages: 21

Brand: National Instruments Pages: 10

Brand: Dahua Pages: 15

Liberty Vertical Picket

Brand: National ramp Pages: 9

Brand: Measurement Computing Pages: 32

Brand: LEGRAND Pages: 3

Productivity 2000 P2-08NAS

Brand: Automationdirect.com Pages: 4

CPX-AP-I-8DI-M8-3P

Brand: Festo Pages: 18

Brand: Sandstrom Pages: 32

EAGLE-GRIP 4 Series

Brand: Easy Lift Equipment Pages: 27

Brand: Castex Pages: 23

Brand: Dannmar Pages: 85

Brand: Wayne Pages: 1

Brand: Niko Pages: 104

Brand: Vidos Pages: 8

Brand: Gude Pages: 7

Brand: FAAC Pages: 16

Brand: Jensen Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands