manualshive.com logo in svg

Technicolor TG672, Setup And User Manual

Share
Download
Technicolor TG672 Setup And User Manual Download Page 33

25

3 MANUAL INSTALLATION

E-DOC-CTC-20100728-0008 v2.0

3.1.1 Setting up your Technicolor Gateway as DSL Gateway

Introduction

This section helps you to connect the Technicolor Gateway to your service provider’s network.

Signal arriving at your home

The 

Line

 signal that arrives at your home consists the following components:

A 

Phone 

signal carrying the traffic for telephony.

A 

DSL

 signal carrying the Internet traffic.

DSL Gateways have a built-in solution to remove the 

Phone

 component. No additional devices are needed, you can 

connect them directly to the 

Line

.

Telephones do not have this capability, so here you have to use a filter or splitter to remove the 

DSL

 signal.

How does a filter/splitter look like

A splitter/filter is a box that typically has the following connectors:

A 

Line

 input

This connector must be connected to the input signal that needs to be filtered.

A 

Phone/PSTN

 output

This connector offers filtered output signal. It only contains the 

Voice

 component and can only be used for connecting 

phones.

A 

Modem/DSL

 output (optional)

This connector offers unfiltered output. It contains both the 

Phone

 and 

DSL

 signal and can be used to connect your 

Technicolor Gateway.

Connecting the cables

The procedure to be followed depends on the fact if this filter has been integrated into your Technicolor Gateway or not.

Check the label of your Technicolor Gateway. If the product name contains:

“wIF” (for example Technicolor TG672 

wIF

) then your Technicolor Gateway has an integrated filter. No external filters 

are needed. Follow the steps described in 

“Scenario 2: A Technicolor Gateway without integrated filter” on page 26

.

No “wiF”

 (for example Technicolor TG672) then your Technicolor Gateway does 

not

 have an integrated filter. Follow the 

steps described in 

“Scenario 2: A Technicolor Gateway without integrated filter” on page 26

.

Scenario 1: A Technicolor Gateway with integrated filter

Proceed as follows:

1

Take the DSL cable. This is the gray cable that is included in your box.

This 

Phone

 signal is only used for communication over the traditional telephone network (PSTN). Voice over IP 

communication will be carried by the 

DSL

 signal.

DSL 

+

 

Voice

Voice

DSL 

+

 

Voice

Service

Provider

Filter/Splitter

LINE

PHONE

MODEM

Summary of Contents for TG672

























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands