manualshive.com logo in svg

Technicolor TG672, Setup And User Manual

Share
Download
Technicolor TG672 Setup And User Manual Download Page 109

101

9 SHARING YOUR USB PRINTER

E-DOC-CTC-20100728-0008 v2.0

9  Sharing Your USB Printer

Introduction

A Technicolor Gateway USB port allows you to share your USB printer in your local network. This way everyone in your 
network can use the same printer without having to buy an expensive network printer. 

Compatibility printer driver

The printer driver which runs on the computer must support unidirectional traffic. This is supported by the majority of 
modern day printers.

In case a multifunctional USB printer is connected to the Technicolor Gateway, the non-printing services may not 
work on your computer.

Restrictions

Only 

one

 USB printer can be connected to your Technicolor Gateway.

Procedure

Proceed as follows:

1

Connect your USB printer to the Technicolor Gateway. For more information, 

“9.1 Connect your USB printer to the 

Technicolor Gateway” on page 102

.

2

Configure the printer sharing service on your Technicolor Gateway.

For more information, see 

“9.2 Configuring The Printer Sharing Service on Your Technicolor Gateway” on page 103

.

3

Install the printer on your computer.

For more information, see 

“9.3 Installing the Printer On Your Computer” on page 105

.

Summary of Contents for TG672

























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands