GAMING CHAIRS MODELS
TS83
,
TS84,
TS
9
0
,
TS
9
2
,
TSF44
,
TSC81
,
XXL2
ATTENTION:
⚠
Follow the instructions step by step.
⚠
To avoid misalignments, leave the screws loose and do not tighten them until all are in their respective places.
⚠
Do not overtighten or force the screws as they could break, strip, or damage the threads of the holes.
⚠
Using the wrong size of screws on a part could result in damage to the screw or the part.
ASSEMBLY INSTRUCTIONS
A
B
C-L
D
E
F
G
H
K
L
M
N
O
P
Q
C-R
I-L
I-R
J-N
J-L
Backrest
Seat
Left Armrest
Right Armrest
Mechanism
Gas Lift
Covers for gas
lift, set of 3 pcs
5-leg star base
Casters, 5 pcs.
Left cover for
seat bracket
Right cover for
seat bracket
Neck pillow
Lumbar pillow
Allen wrench
STEP
1
Insert the casters
Ⓗ
into the legs of the base
Ⓖ
using
pressure, then place the gas lift
Ⓔ
in the middle of the
base and cover it with
Ⓕ
.
Ⓜ
STEP
2
STEP
3
STEP
4
Note: When sitting on chair, not looking at it
M8x20mm,
4 pcs
M8x25mm,
12 pcs
M5x12mm,
2 pcs
O-Rings,
16 pcs
Washers,
16 pcs
Hole Covers,
4 pcs
Ⓖ
Ⓔ
Ⓗ
Ⓕ
Ⓛ
Ⓞ
Ⓟ
O-Ring in
the middle!
Ⓓ
(
Front
)
C-L
C-R
Note: The armrest side is determined by you sitting on the chair, not looking at it
(Back)
C-L
LEFT
C-R
RIGHT
Ⓑ
Assemble the armrests
and in their respective
sides of the seat
Ⓑ
using screws
Ⓜ
, O-rings
Ⓞ
and
washers
Ⓟ
.
Ⓐ
Put the seat over the base parts making sure the tip of
the gas lift enters into the hole of the mechanism, then
assemble the backrest
Ⓐ
to the metal brackets on
both sides of the seat
Ⓑ
using screws
Ⓜ
, O-rings
Ⓞ
and washers
Ⓟ
.
Ⓑ
ⓄⓅ
O-Ring in
the middle!
Ⓜ
Attach the covers and to the brackets on their
respective sides of the seat
Ⓑ
using screws
Ⓝ
and
cover the holes with
Ⓠ
As shown.
I-L
I-R
STEP
5
I-R
I-L
LEFT
RIGHT
Ⓑ
Ⓝ
First attach the lumbar pillow then the neck pillow
by fastening the buckles behind the backrest
Ⓐ
as
shown.
J-L
J-N
STEP
6
Ⓐ
(This shows
The chair
from behind)
J-N
J-L
(Mechanism)
(Backrest, armrest)
4 sets
Ⓞ
Ⓟ
O-Ring in
the middle!
8 sets
(Brackets Covers)
Ⓠ
4 pcs
felt gaskets,
4 pcs
R
C-R
RIGHT
R
R
Ⓑ
Ⓓ
A
B
C-L
D
E
F
G
H
R
Turn over
the seat
Ⓑ
with its back end towards you
,
as shown
below. Place
Ⓠ
on the four seat mechanism
holes
. Use
screws
Ⓛ
, O-rings
Ⓞ
and washers
Ⓟ
to install the
mechanism
Ⓓ
with its knob facing towards the front.
Except
TS84
(
Back
)