4
External Connectors
TEK5-APL
Quickstart Guide
3
Installation Instructions
This section describes the mounting procedures for TEK series device. The material in the mounting area must provide sufficient strength for support of this embedded
box PC.
3.1
Surface Mounting
There are 4 mounting holes (M5) on the top side of the device required for surface mounting. Four M4 or M5 screws with at least 8mm head-to-tip length are required
to secure this device to the surface.
INNOVATORS OF TECHNOLOGY
2
Dimensions
1
Safety Precautions
Thank you for purchasing a TechNexion TEK series device. This installation guide will be helpful in the installation, wiring and inspection of your TechNexion embedded
fanless box PC. Before using the product, please read this guide to ensure correct use. You should thoroughly understand all safety precautions before proceeding with
the installation, wiring, and operation. Place this instruction sheet in a safe location for future reference. The following suggestions will help you.
• Keep the device dry. Precipitation, humidity, and all types of liquids or moisture can contain minerals that will corrode electronic circuits. If your device does get wet,
allow it to dry completely.
• Do not use or store the device in dusty or dirty areas. Its parts and electronic components can be damaged.
• Do not store the device in hot areas. High temperatures can shorten the life of electronic devices, damage batteries, and warp or melt certain plastics.
• Do not store the device in cold areas. When the device returns to its normal temperature, moisture can form inside the device and damage electronic circuit boards.
• Do not attempt to open the device. This product is designed for specific applications and needs to be installed by qualified personnel.
• Do not drop, knock, or shake the device. Rough handling can break internal circuit boards and fine mechanics.
• Do not paint the device. Paint can clog the parts and prevent proper operation.
• Unauthorized modifications or attachments could damage the device and may violate regulations governing radio devices.
• Do not touch any internal or exposed parts of the device as electrical shock may result.
• Do not open the device while power is on. Otherwise electrical shock may result.
• Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the device.
• Be sure the ventilation holes are not obstructed during operation. Otherwise malfunction may result due to bad ventilation or overheating.
These suggestions apply equally to your device, battery, charger, or any enhancement. If any device is not working properly, take it to the nearest authorized service
facility for service.
•Make sure that the available power source matches the required input power of the device. Failure to observe this caution may result in electric shock or fire.
•Do not power the unit by DC input when you apply power over the PoE (RJ45).
1.1
Storage and Installation
1.2
Wiring
1.3
Maintenance and Inspection
!
Unit : mm
Description
No.
No.
Description
1
2A
2B
3
4
5A
5B
6
7
8
9
10
11A
11B
12
13
14
15
16
17
18
19A
19B
19C
19D
20
21
22
23
24A
24B
24C
25
Power Input connector
SIM1 (Mini-SIM) card slot
SIM2 (Mini-SIM) card slot
microSD card slot
2x USB 3.0 Host connector
2x USB 2.0 Host connector
2x USB 2.0 Host connector
LED Light 1/2/3/4 indicators
Power LED indicator
SATA LED indicator
Power button
Reset button
Antenna hole
Antenna hole
Grounding screw
LAN1 RJ45 connector
LAN2 RJ45 connector
OPT-A connector hole
OPT-B connector hole
2.5” SSD Drive Rack
GPIO DB15 connector
RS-XXX1 (Serial Port) DB9 connector
RS-XXX2 (Serial Port) DB9 connector
RS-XXX3 (Serial Port) DB9 connector
RS-XXX4 (Serial Port) DB9 connector
DVI-D connector
DP connector
3.5mm jack Mic in
3.5mm jack Line out
Antenna hole
Antenna hole
Antenna hole
VGA (15-pin D-SUB) connector
4
6
7 8 9
Front view:
1 2A
2B
10
5A
3
11A
11B
24A
19D
19B
24B
24C
12 5B
15
13
16
17
25
14
Rear view:
18 19C
19A
21
20
22 23
1
2
286
145
110
250
145 60
170
180
4.2
270
67.7
65.5
