background image

409-35013 

Rev A 

of 8 

SAFETY PRECAUTIONS 

 AVOID INJURY 

 READ THIS FIRST! 

Safeguards are designed into this application equipment to protect operators and maintenance personnel from 
most hazards during equipment operation. However, certain safety precautions must be taken by the operator 
and repair personnel to avoid personal injury, as well as damage to the equipment. For best results, application 
equipment must be operated in a dry, dust-free environment. Do not operate equipment in a gaseous or 
hazardous environment. 

Carefully observe the following safety precautions before and during operation of the equipment:

Always wear approved eye protection while operating 
equipment. 

Always wear appropriate ear protection while using 
equipment. 

Moving parts can crush and cut. Always keep guard(s) 
in place during normal operation.  

Electrical shock hazard. 
 

Always turn off the main power switch and disconnect 
the electrical cord from the power source when 
performing repair or maintenance on the equipment.  

Never insert hands into installed equipment. 
Never wear loose clothing or jewelry that may catch in 
moving parts of the equipment. 

Never alter, modify, or misuse the equipment. 

 

 SUPPORT CENTER

 

CALL TOLL FREE 1-800-522-6752 (CONTINENTAL UNITED STATES AND PUERTO RICO ONLY) 

The 

Support Center

 offers a means of providing technical assistance when required. In addition, Field Service 

Specialists are available to provide assistance in the adjustment or repair of the application equipment when 
problems arise which your maintenance personnel are unable to correct. 

INFORMATION REQUIRED WHEN CONTACTING THE SUPPORT CENTER 

When calling the Support Center regarding service to equipment, it is suggested that a person familiar with the 
device be present with a copy of the manual (and drawings) to receive instructions. Many difficulties can be 
avoided in this manner.  

When calling the Support Center, be ready with the following information:

1.  Customer name 

2.  Customer address 

3.  Person to contact (name, title, telephone number, and extension) 

4.  Person calling 

5.  Equipment number (and serial number if applicable) 

6.  Product part number (and serial number if applicable) 

7.  Urgency of request 

8.  Nature of problem 

9.  Description of inoperative component(s) 

10.  Additional information/comments that may be helpful 

 

 
 

Summary of Contents for AMP 5K/30









Reviews: