manualshive.com logo in svg

TDK HAL 3900, User Manual

Share
Download
TDK HAL 3900 User Manual Download Page 17

 

 
TDK-Micronas GmbH 

 

Page

 17

 of 

23

 

 

Figure 38: Calibration Points 

 

4.2   Evaluation Software Instructions 

1.  Extract the file Joystick_Module_Environment.zip on your Computer.

 

2.  Connect the preferred Communication Device to the Computer USB port and the Joystick Module 

PCB.

 

3.  Run Joystick_Module_Environment.exe.

 

4.  If the Sensor is used for the first time (or the sensor is not programmed via HAL 3900 PE)

 

a.  Navigate to the Configuration Tab 

b.

 

Select the programming device you are using TDK SPI Programmer or MSP

 

c.

 

Select the Sensor to be programmed

 

d.

 

Click the appropriate chip select setting

 

e.

 

Press Program Sensor, a message appears showing the status of the process.

 

5.  Navigate to the Main tab

 

6.  Make Sure the Com Mode is set to Auto and press Start.

 

7.  Once communication to the sensor is established you are redirected to the Magnetic Field Tab

 

8.  When the 3D environment is loaded, the Joystick Tab is available and the progress bar stops flashing.

 

9.  Press Stop Application to Terminate the program

 

 

 

Summary of Contents for HAL 3900
























Reviews:

No comments

Brands by name

Popular brands

Load more brands