manualshive.com logo in svg

TBK vision TBK-NVR2200 Series, User Manual, Page: 26 / 216

Share
Download
TBK vision TBK-NVR2200 Series User Manual Download Page 26

TBK-NVR2200 Network Video Recorder User Manual  V2 

 

 

 

www.tbkvision.com

 

 

 

26

 

 
 
 
 
TBK-NVR2208-8P   

 

 

Table 1-8

 

Panel Description 

 

No. 

 

Item 

 

Description 

 

1 

 

Power Supply 

 

100~240 VAC power supply.  

 

2 

 

Audio In 

 

RCA connector for audio input. 

 

3 

 

HDMI Interface 

 

HDMI video output connector. 

 

4 

 

LAN Network Interface 

 

1 10 /100 /1000 Mbps self-adaptive Ethernet interface 

 

5 

 

Audio Out 

 

RCA connector for audio output. 

 

6 

 

VGA Interface 

 

DB9 connector for VGA output. Display local video output 
and menu. 

 

7 

 

USB Interface 

 

Universal  Serial  Bus  (USB)  ports  for  additional  devices 
such as USB mouse and USB Hard Disk Drive (HDD). 

 

8 

 

Ground 

 

Ground (needs to be connected when NVR starts up). 

 

9 

 

Power Switch 

 

Switch for turning on/off the device. 

 

10 

 

Network 

 

Interfaces 

with PoE function 

 

Network interfaces for the cameras and to provide power 
over Ethernet. 

 

 

 

Summary of Contents for TBK-NVR2200 Series

























































































































































































































Reviews:

No comments