INSTALLATION INSTRUCTIONS
A
B
TURN OFF
TURN OFF
SI
LI
CO
NE
Your installation may require new supply
lines. (Supply lines are not included.)
® REGISTERED TRADEMARK OF TAYMOR INDUSTRIES LTD.
CUSTOMER SERVICE WEST 1-800-267-4774 | EAST 1-800-387-7064 | taymor.com
THIS FAUCET MEETS OR EXCEEDS THE FOLLOWING STANDARDS:
cUPC, ASME A112.18.1, NSF-61 AND LOW LEAD COMPLIANT
THANK YOU
FOR PURCHASING THIS TAYMOR PRODUCT. ALL TAYMOR PRODUCTS ARE CAREFULLY
ENGINEERED AND FACTORY TESTED TO PROVIDE LONG TROUBLE-FREE USE UNDER NORMAL CONDITIONS.
HAVE BASIC TOOLS READY
RECOMMENDED TOOLS:
1
Flashlight
Teflon tape Screwdrivers
Adjustable
wrench and
pipe wrench
Plumber’s putty
Safety goggles
Torque wrench
Silicone caulk
5
ATTACH THE HOT AND COLD SUPPLY LINES
Apply teflon tape onto threaded ends of faucet inlets. Connect water supply lines to faucet inlets. Hot
water supply lines go into left inlet. Cold water supply lines go into right inlet. (Supply lines are not
included.) Use two wrenches when tightening. Do not over tighten.
FOR PLASTIC AND BRAIDED
STAINLESS STEEL SUPPLY TUBES
FOR 3/8” O.D. BALL-NOSE SUPPLY TUBES
IF THE SUPPLY TUBE END HAS A BULBOUS SHAPE, USE
THE SUPPLIED COUPLING NUTS.
THESE SUPPLY TUBES HAVE INTEGRAL NUTS. JUST SCREW
THE NUT ONTO THE FAUCET INLET.
6
7
TORQUE
22 – 30 FT/LBS.
TORQUE
22 – 30 FT/LBS.
EXPLODED
DIAGRAM FOR
REFERENCE
MAINTENANCE
Your new faucet is designed
for years of trouble-free
performance. Keep it looking new
by cleaning it periodically with
a soft cloth. Avoid abrasive
cleaners, steel wool and harsh
chemicals as these will dull the
finish and void your warranty.
FLUSHING & AERATOR CLEANING
Remove the aerator by turning it counterclockwise. Remove the internal parts of the aerator by push-
ing them out with your fingers. Remove any debris. Turn on hot and cold water supplies. Turn faucet
handle all the way on and run water through the spout for about a minute to remove debris. While
water is running check all connections for leaks. Reassemble the aerator and screw it back into the
spout hand tight.
3
FAUCET INSTALLATION
A)
Screw the threaded bolt into escutcheon.
B)
Apply a bead of plumber’s putty or silicone caulk around the sink openings. Install the gasket over
the three holes in your sink.
C)
Install faucet through the holes of the sink. Center the faucet body on the sink. From underneath the
sink, hand tighten the mounting nut #22. Secure the faucet with washers #18 and #19 and mounting
nut #24.
Do not over tighten.
Don’t use plumber’s putty on cultured marble or other composite sinks.
Putty will discolour the sink.
2
TURN OFF THE MAIN WATER SUPPLY
Locate water supply inlets and shut off water supply valves. These are usually found under
the sink.
WARNING: READ ALL
the instructions completely before beginning installation.
READ ALL
warnings, care and maintenance information.
Taymor recommends calling a professional if you are uncertain about installing this product!
This product should be installed in accordance with all local and provincial plumbing and building codes.
Need Help?
Please call our toll-free Customer Support line at
(WEST) 1-800-267-4774 (EAST ) 1-800-387-7064 for additional assistance or service.
C
1 - HANDLE
A
4
SPRAY INSTALLATION
A)
Insert spray support through far right hole on escutcheon. From underneath the sink, screw nut
onto shank and hand tighten.
B)
Insert spray hose down through support and sink. Attach spray hose to spray hose nipple. Tighten
with wrench.
B
2 - SET SCREW
3 - INDEX
4 - BONNET
5 - CAP
6 - CARTRIDGE
7 - SLEEVE
8 - SPOUT
9 - AERATOR
ASSEMBLY
10 - WASHER
11 - O-RING
12 - RETAINER
13 - DIVERTER
14 - BODY
15 - SPRAY
ASSEMBLY
16 - ESCUTCHEON
17 - BASE PLATE
18 - PLASTIC
WASHER
20 - BOLT
19 - METAL
WASHER
21 - BOLT
22 - MOUNTING NUT
23 - COUPLING NUT
24 - MOUNTING NUT
GASKET
AERATOR
AERATOR
SHELL
INFINITY 06-8837SSS
SINGLE HANDLE KITCHEN FAUCET
