background image

INSTALLATION INSTRUCTIONS

 

MAKE CONNECTIONS TO WATER LINES

Use 1/2” IPS faucet connections (1) and tighten connections with wrench. Or use the supplied plastic 
coupling nuts (3) with 3/8” O.D. ball-nose risers (2), hand tighten only. Do not overtighten. Do not use 
metal coupling nuts (4). Do not use plumber’s putty, pipe dope, or any other type of sealing com-
pound on water inlet or threads. Additional compound is not necessary.

CUSTOMER SERVICE      WEST 1-800-267-4774   |   EAST 1-800-387-7064   |   taymor.com

® REGISTERED TRADEMARK OF TAYMOR INDUSTRIES LTD.

A

B

TURN OFF

TURN OFF

4

SI

LI

CO

NE

THIS FAUCET MEETS OR EXCEEDS THE FOLLOWING STANDARDS:

cUPC, ASME A112.18.1, NSF-61 AND LOW LEAD COMPLIANT

1

2

3

1

4

THANK YOU

 FOR PURCHASING THIS TAYMOR PRODUCT. ALL TAYMOR PRODUCTS ARE  CAREFULLY  

ENGINEERED AND FACTORY TESTED TO PROVIDE LONG TROUBLE-FREE USE UNDER NORMAL CONDITIONS.

HAVE BASIC TOOLS READY

RECOMMENDED TOOLS:

1

Flashlight

Teflon tape Screwdrivers

Adjustable and

Pipe wrench

Plumber’s putty

Safety goggles

Torque wrench

Silicone caulk

5

6

EXPLODED DIAGRAM FOR REFERENCE 

MAINTENANCE

 Your new faucet is designed for years of trouble-free performance. Keep it 

looking new by cleaning it periodically with a soft cloth. Avoid abrasive cleaners, steel wool 
and harsh chemicals as these will dull the finish and void your warranty.

HAND TIGHTEN THE WING NUTS

From underneath the sink, hand tighten the wing nuts. Tighten gently until snug and alternate from side 
to side to seat the faucet body evenly.

Don’t over tighten

FLUSHING & AERATOR CLEANING

Remove the aerator by turning it counterclockwise. Remove the internal parts of the aerator by push-
ing them out with your fingers. Remove any debris. Turn on hot and cold water supplies. Turn faucet 
handles all the way on and run water through the spout for about a minute to remove debris. While 
water is running check all connections for leaks. Reassemble the aerator and screw it back into the 
spout hand tight.

3

GASKET & FAUCET INSTALLATION

A)

 Apply a bead of plumber’s putty or silicone caulk around the sink openings.

B)

 Install the gasket over the three holes in your sink.

C) 

Install faucet shanks through the holes of the sink. Centre the faucet body on the sink.

Don’t use plumber’s putty on cultured marble or other composite sinks. 
Putty will discolour the sink.

2

TURN OFF THE MAIN WATER SUPPLY

Locate water supply inlets and shut off water supply valves. These are usually found under 
the sink.

WARNING: READ ALL

 the instructions completely before beginning.  

READ ALL

 warnings, care and maintenance information.

Taymor recommends calling a professional if you are uncertain about installing this product!

This product should be installed in accordance with all local and provincial plumbing and building codes.

Need Help?

 Please call our toll-free Customer Support line at 

(WEST) 1-800-267-4774     (EAST ) 1-800-387-7064 for additional assistance or service.

C

06-4481

TWO HANDLE BAR FAUCET

Your installation may require new supply 

lines. (Supply lines are not included.)

7

1 - INDEX

2 - SCREW

3 - HANDLE

4 - BONNET

5 - WASHER

6 - CARTRIDGE

7 - SEAT

8 - SPRING

9 - ESCUTCHEON

10 - BODY

11 - BASE PLATE

12 - MOUNTING NUT

13 - COUPLING NUT

14 - CLIP

15 - O-RING

16 - WEARABLE RING

17 - NUT

18 - SPOUT

19 - AERATOR WASHER

20 - AERATOR

21 - AERATOR SHELL

Reviews: