Taylor-Dunn RE-380-36 Service And Replacement Parts Manual Download Page 133

Page: 133 / 150

Replacement Parts

Page 133

* Not available at time of printing

MR-380-05

RE-380-36 & RE-380-48

FRAME AND BODY (P2)

Cab Accessories

Item No. Part No.

Description

Qty

72-023-20

Strobe Light, Amber

88-025-06

#8-32 X 1/2” Truss Head Screw

88-028-62

#8 Lock washer

88-029-80

#8-32 Nut

98-606-00

3/16” ID Grommet

92-201-00

4-1/2” X 8-1/2” Mirror

1 or 2

92-202-12

Left Mounting Bracket

92-202-13

Right Mounting Bracket

92-202-15

Spacer for Mounting Bracket

1 or 2

91-814-16

Left Hinge, Female

91-814-17

Right Hinge, Female

88-069-81

1/4”NC Locknut

88-060-22

1/4”NC X 3-1/2” HEX Head Bolt

88-068-61

1/4” SAE Washer

2 or 4

88-065-09

1/4”NC X 3/4” Phillips Truss Head Screw

2 or 4

88-068-62

1/4” Lock washer

2 or 4

88-069-83

1/4”NC Acorn Nut

2 or 4

92-206-00

Inside Mirror

02-210-70

Inside Mirror Bracket

88-065-09

1/4” X 3/4” Phillips Truss Head Screw

88-068-67

1/4” Internal Toothed Lock washer

88-069-80

1/4” NC Nut

Not Shown

92-207-00

Mirror, multi-panel

91-810-00

Mounting bracket for multi-panel mirror

Not Shown

75-114-16

Wiring Harness for Wiper and Light

Summary of Contents for RE-380-36























































































































































Search results

Summary of Contents for RE-380-36

Reviews:

Taylor-Dunn RE-380-36, Service And Replacement Parts Manual, Page: 133 / 150

Search results

Summary of Contents for RE-380-36

Reviews: