Transmission
Page 3
MB-T48-02
T-48 AC / ET 3000
REAR HUB OR ROTOR
Note: The torque specification for the axle hub bolt is listed in the Hardware
Torque Table at the end of this section. An impact wrench will be
required to remove the bolt.
Note: The axle hub bolt has a special thread locking compound applied
to the threads. If this bolt is removed, it must be replaced.
1. Make sure the key-switch is in the “OFF”
position, then remove
the key.
2. Place the forward-reverse switch in the center “OFF” position.
3. If equipped with a hand operated park brake, set the brake.
4. Place blocks under the front wheels to prevent vehicle movement.
5. Disconnect the main positive and negative cables at the batteries.
Always use a lifting strap, hoist, and jack stands, of adequate capacity
to lift and support the vehicle. Failure to use lifting and support devices
of rated load capacity may result in severe bodily injury.
6. Raise the wheel off of the ground.
7. Remove the tire/wheel assembly, Refer to
Tires and Wheels
section for information
regarding removing the tire/wheel assembly.
8. Remove the axle hub bolt and washer
and remove the hub from the axle.
9. Remove the outer brake pad. Refer to
section
Brake Service
for information
regarding removing the brake pads.
10. Remove the rotor.
11. Install in reverse order.
a. Lightly grease the axle splines.
b. Refer to section
Brake Service
for information regarding installing the brake pads.
c. Thoroughly clean the threads in the axle shaft.
d. Using a new bolt, torque the axle hub bolt to the specified number found in the Hardware
Torque Table at the end of this section.
e. Refer to
Tires and Wheels
section for information regarding installing the tire/wheel assembly.
12. Lower the wheel to the ground.
13. Reconnect the main positive and negative cables at the batteries.
14. Remove the blocks from behind the wheels, release the park brake and test drive the vehicle.
The axle retaining plate bolts have a pre-applied thread locking
compound. They are intended for one time use only. If removed they
must be replaced. Reusing the original bolts could cause loss of brakes
resulting in severe bodily injury and/or property damage.
Refer to section
Rear Brakes
in
Illustrated Parts
for the part number
of the bolt.
Summary of Contents for ET 3000
