Taylor-Dunn E0-455-24 Service And Replacement Parts Manual Download Page 36

Page: 36 / 134

Transaxle - GT

Page 36

E-455

ME-455-04

AXLE SHAFT

The oil level in the housing is above the bottom of the axle flange. To minimize oil spills, raise the side of the vehicle

high enough so that the oil level is below the bottom of the axle flange. If both axles have to be removed at the same

time then all oil must be drained from the housing.

Note: This procedure does not require that the rear end or drive assembly be removed from the vehicle.
Note: The axle hub bolt has a special thread locking compound applied to the threads. If this bolt is removed,

it must be replaced.

Note: The hub or rotor does not have to be removed but if they are to be replaced, then remove them before

removing the axle from the housing.

This section is one section of a complete service

manual. Before starting any procedure, read all

warnings and instructions that are located in the

Service Guidelines chapter.

WARNING

The axle retaining plate bolts have a pre-applied

thread locking compound. They are intended for one

time use only. If removed they must be replaced.

Reusing the original bolts could cause loss of brakes

resulting in severe bodily injury and/or property

damage.

WARNING

Install

11: Install in reverse order or removal

a. Lubricate the bearing external O-ring.

b. Use new bolts for the axle retaining plate.

c. If the wheel hub was removed, install the hub

and rotor. Torque the hub bolt to the specification

listed in the table at the end of this section.

12:

Fill with oil to the level of the fill plug threads.

Refer to Check Oil Level procedure.

13: Set the park brake.

14: Lower the vehicle.

15: Reconnect the batteries.

16: Remove the blocks from behind the

wheels.

17: Release the park brake and test drive.

Remove

1: Disconnect the batteries.

2: If required, drain the oil. Refer to Change Oil

Procedure.

3: Raise the rear of the vehicle and support with

jack stands.

4: Release the park brake.

5: Remove the tire and wheel assembly. Refer

to Tires and Wheels section for information

regarding removing the tire and wheel assembly.

6: Remove the four bolts attached to the axle

retaining plate.

7: Remove the axle retaining plate and brake body

assembly as one unit.

8: Secure the brake body assembly, do not let it

hang by the brake hose.

9: Pull the axle out of the housing.

10: Inspect all bearings for roughness or play, replace

as needed.

Summary of Contents for E0-455-24







































































































































Search results

Summary of Contents for E0-455-24

Reviews:

Related manuals for E0-455-24

Brands by name

Popular brands

Taylor-Dunn E0-455-24, Service And Replacement Parts Manual

Search results

Summary of Contents for E0-455-24

Reviews:

Related manuals for E0-455-24

Brands by name

Popular brands