AFTER SALES SUPPORT
1300 922 271
9
m
To ensure that the LI battery pack provides long
service you should take care to recharge it promptly.
You must recharge the battery pack when you notice
that the power of the cordless drill drops.
Never fully discharge the battery pack. This will
cause the LI battery pack to develop a defect.
7.2 Torque setting (Fig. 5)
selector (1).
with the torque selector (1). The correct torque
depends on several factors:
•
on the type and hardness of material in
question
•
on the type and length screws used
•
on the requirements needing to be met by the
screwed joint.
The clutch disengages with a grating sound to
indicate when the set torque is reached.
Important!
The tool must be at a standstill when
you set the torque with the torque selector (1).
7.3 Drilling (Fig. 5)
For drilling purposes, move the torque selector (1) to
the last step “Drill”. In this setting the slip clutch is
inactive. The maximum torque is available in drilling
mode.
7.4 Forward/Reverse switch (Fig. 6)
With the Forward/Reverse switch (2) above the
On/Off switch (3) you can select the direction of
rotation of the battery powered drill/screwdriver
and secure it against being switched on accidentally.
You can choose between forward and reverse
rotation. To avoid causing damage to the gearing it
is advisable to change the direction of rotation only
when the tool is at a standstill. The On/Off switch (3)
is blocked when the Forward/Reverse switch (2) is in
centre position.
7.5 On/Off switch (Fig. 6)
On/Off switch (3). The further you press the
On/Off switch (3), the higher the speed of the
battery-powered drill/screwdriver.
7.6 Battery capacity indicator (Fig. 5)
Press the button for the battery capacity indicator
(11). The battery capacity indicator (10) indicates the
charge state of the battery on 3 colored LEDs.
All LEDs illuminate:
The battery is fully charged.
The yellow and red LED illuminate:
The battery has an adequate remaining charge.
Red LED illuminates:
The battery is empty, recharge the battery.
7.7 Changing the accessory (Fig. 7)
Important!
Set the Forward/Reverse switch (2)
to its centre position whenever you carry out
any work (for example changing the accessory,
maintenance work, etc.) on the cordless drill.
•
chuck (7) with an automatic spindle stop.
•
Open the chuck (7) by turning it counter-
clockwise. The chuck opening (b) must be
large enough to hold the accessory (drill bit
or screwdriver bit).
•
Select the suitable accessory. Push the
accessory as far as possible into the chuck
opening (b).
•
Tighten the chuck (7) by turning it clockwise
and then check that the accessory is secure.
7.8 Screwdriving
We recommend using self-centering screws (e.g.
Torx screws, recessed head screws) designed for
reliable working. Be sure to use a bit that matches
the screw in shape and size. Set the torque, as
described in Section 7.2 in the user guide to suit
the size of screw.
7.9 Selecting 1st gear to 2nd gear (Fig. 5)
By adjusting the selector switch (6), you can work
with a faster or slower turning speed. Change
the gear only when the drill is at a standstill. If
you fail to observe this point, the gearing may be
damaged.
8. Cleaning, maintenance
and ordering of spare parts
Important!
Always pull out the mains power plug
before starting any cleaning work.
8.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could
attack the plastic parts of the equipment.
Ensure that no water can seep into the
device.
8.2 Maintenance
There are no parts inside the equipment which
require additional maintenance.
MODEL NUMBER: BT-CD 10.8 Li,
01/13
