background image

  

Taurus Super-S Combo                                                                                 User Guide 

Page 12  /  Chapter 3 - System Set Up 

 

 

 

Mac OS 

 

For Mac OS X, use the disk utility to format and create 

partitions on your external disk. 

If the drive does not 

sure

flicts 

 

appear on the 

desktop, make 

there are no 

extension con

and the power is 

turned on! 

 

 

 

 

Only one single 

volume will be 

 

ives. 

visible instead of

two separate dr

 

 

 

In order for the 

computer to access 

han 

 

.: 

 

volumes larger t

2TB, both the 

hardware and OS 

need to have th

capacity to support

large volumes (e.g

WinVista 32bit/64bit

or Mac OS 10.4 and 

above). 

 

  Select “Disk Utility” in the utilities folder 

  Choose your external drive and format it according to your 

requirements 

 

 

 

For Mac OS X, we recommend formatting the drive using the 

native Mac file system HFS+ also known as Mac OS Extended. 

 

If you want to use your drive on a PC running Microsoft 

Windows as well as on your Mac, we recommend you to use 

the FAT32 file system. On your Mac, select MS-DOS when 

formatting it. Note: The file size for a single file on FAT32 is 

limited to 4GB. 

 

 

 

 

 

 

Summary of Contents for Super-S Combo
















Reviews: