manualshive.com logo in svg

TASKalfa 3011i, Operation Manual

The TASKalfa 3011i is an advanced multifunctional printer designed for efficient office use. With its user-friendly interface, it becomes easier to operate and manage various office tasks. To explore its full potential, download the free Operation Manual from our website manualshive.com to access detailed instructions and maximize productivity.

Share
Download
background image

1-7

Legal and Safety Information > Notice

Safety Instructions Regarding the Disconnection of 

Power

Caution

: The power plug is the main isolation device! Other switches on the equipment are only functional switches and 

are not suitable for isolating the equipment from the power source.

Attention:

 Le débranchement de la fiche secteur est le seul moyen de mettre l'appareil hors tension. Les interrupteurs 

sur l'appareil ne sont que des interrupteurs de fonctionnement: ils ne mettent pas l'appareil hors tension.

Compliance and Conformity

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of 
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential 
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in 
accordance with the instructions, may cause harmful interference to radio communications. However, there is no 
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to 
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try 
to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
• The use of a non-shielded interface cable with the referenced device is prohibited.

CAUTION . The changes or modifications not expressly approved by the party responsible for compliance could void the 
user's authority to operate the equipment.

This device contains the module (FCC ID: E522K3A0512, IC: 1059B-2K3A0512), which complies with Part 15 of FCC 
Rules and RSS-Gen of IC Rules.

Operation is subject to the following two conditions; (1) this device may not cause interference, and (2) this device must 
accept any interference, including interference that may cause undesired operation of the device.

Radio Tag Technology

In some countries the radio tag technology used in this equipment to identify the toner container may be subject to 
authorization and the use of this equipment may consequently be restricted.

Other precautions 

(for users in California, the United States)

Perchlorate Material - special handling may apply. See 

www.dtsc.ca.gov/hazardouswaste/perchlorate

.

Summary of Contents for 3011i



































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 3011i

Chamjin I&C CJ50SP User Manual preview
CJ50SP
Brand: Chamjin I&C Pages: 21
Sagem MF9500 Facsimile Operation Manual preview
MF9500
Brand: Sagem Pages: 83
Canon GP160DF Service Manual preview
GP160DF
Brand: Canon Pages: 797
Canon LASER CLASS 730i User Manual preview
LASER CLASS 730i
Brand: Canon Pages: 155
Oki C710cdtn User Manual preview
C710cdtn
Brand: Oki Pages: 72
Olivetti PG 2028 SPECIAL Operation Manual preview
PG 2028 SPECIAL
Brand: Olivetti Pages: 104
M&R Starlight A50 Manual preview
Starlight A50
Brand: M&R Pages: 36
Xante Accel-a-Writer 8200 Manual preview
Accel-a-Writer 8200
Brand: Xante Pages: 12
Intellisystem ThermalTronix TT-1025EX-MIL User Manual preview
ThermalTronix TT-1025EX-MIL
Brand: Intellisystem Pages: 11
Ricoh SP C222DN Administration Manual preview
SP C222DN
Brand: Ricoh Pages: 284
Xante Accel-a-Writer 4 Maintenance And Specifications preview
Accel-a-Writer 4
Brand: Xante Pages: 12
Oki C6050n Installation preview
C6050n
Brand: Oki Pages: 2
Xerox VersaLink C620 Installation Manual preview
VersaLink C620
Brand: Xerox Pages: 2
Oki B2520 Brochure & Specs preview
B2520
Brand: Oki Pages: 2
Nagel 2S Trimmer Installation Manual preview
2S Trimmer
Brand: Nagel Pages: 22
Epson 5700i - EPL B/W Laser Printer Setup Manual preview
5700i - EPL B/W Laser Printer
Brand: Epson Pages: 33
Epson 2180 - LQ B/W Dot-matrix Printer Specifications preview
2180 - LQ B/W Dot-matrix Printer
Brand: Epson Pages: 2
Epson 2190 - FX B/W Dot-matrix Printer Specifications preview
2190 - FX B/W Dot-matrix Printer
Brand: Epson Pages: 2

Brands by name

Popular brands

Load more brands